Models > AER5822VAD0 > Instructions

AER5822VAD0 Amana Range - Instructions

Jump to:

All Instructions for the AER5822VAD0

Customer:: Linda from SAINT CLOUD, MN
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Vincent from SHILOH, IL
Parts Used:: WP9761958
Difficulty Level:: Very Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Electric contact connection melted, shorting out the range.

After unplugging electric service, loosened 3 Philips-head screws holding 3 wires from range and loosened 3 nuts holding wires from electric cord. Also removed 1 Philips-head screw holding grounding tab. Removed 2 Philips-head screws and removed the old block. Mounted new block with those screws and replaced and tightened all 6 wires.

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Bruno from LE ROY, NY
Parts Used:: WP8523175
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

bottom piece of range rusty

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: patrick from HUGHESTOWN, PA
Parts Used:: WPW10181986
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

temp sensor went oven not heating

the hardest part was moving stove to trplace part

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: William from HADLEY, PA
Parts Used:: WPW10310922, W10761018, W10761014, W10491985
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Broken Trim Pieces

Remove vent trim from oven and set oven glass to the side. Next remove handle from vent trim (two screws). Next place handle on new vent trim. Place glass in place, (it is held in place by bottom of oven door and vent trim). next place side trim in place and place that side of the vent trim and loosely tighten screw holding trim into place at top of the glass. Next place the other trim into place under the vent trim and tighten the screws on both sides.

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Normand from Lincoln, RI
Parts Used:: W10856603
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Broiler element not working

It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

6 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Dorothy from PORT ST LUCIE, FL
Parts Used:: WPW10299224
Difficulty Level:: A Bit Difficult
Total Repair Time:: More than 2 hours
Tools:: Screw drivers

The door wouldn't close.

Watched a video on you tube!
When I ordered the hinge it was recomended to replace both hinges. so I ordered two hinges not knowing that one of the hinges didn't have a spring. I ended up with an extra hinge.

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Kenneth from AUBURNDALE, FL
Parts Used:: W11171119
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Burned out heating element.

I watched the video you provide and it answered all my questions. You estimate repair at 10 minutes. My wife said I waz done in under 10 minutes Watch the video, it explained every step and all the little tricks to the snap connections.

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Rhonda from Logan, OH
Parts Used:: WPW10308477
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

The oven was blowing a circuit.

Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: John from Maysville, GA
Parts Used:: WP8053334
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Broken rear stove drawer glide

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Joseph K from PAHRUMP, NV
Parts Used:: WP3196548
Difficulty Level:: Very Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

The oven light shorted out causing the safety thermostat to blow.

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: David from BURNSVILLE, MN
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Oven Temp inaccurate

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Donald from Byron, MI
Parts Used:: WP3149400
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Top burner would not turn off at any time.

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Lana from WATERVILLE, ME
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven stopped heating, error message stated heating element

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Howard from CROWNSVILLE, MD
Parts Used:: WPW10299224
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

The hinge was mounted on the right . The screw to remove it got it's square head chewed up because of using the wrong ssize driver

I left the old broken hinge in place, & put the new hinge on the left side.

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the AER5822VAD0