Models > AER5823XCW1 > Instructions

AER5823XCW1 Amana Range - Instructions

Jump to:

All Instructions for the AER5823XCW1
61 - 75 of 185
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Melissa from MILL CITY, OR
Parts Used:
WPW10308477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Extremely easy repair
Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from COLUMBIA, TN
Parts Used:
WPW10308477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Heating element, broken
Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rebecca from LANCASTER, SC
Parts Used:
WPW10308477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Baking element had burned into
The video was very helpful.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from SALEM, OR
Parts Used:
WPW10200660, WPW10031790
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replaced screw
By hand screwdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wilton from CANYON LAKE, TX
Parts Used:
WPW10308477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Oven bake would not heat up at all.
Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!

NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alexander from LINCOLN, NE
Parts Used:
WPW10308477, WP3196174
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Bake element was broken
Remove the old part and install the new part.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from GREENBRIER, TN
Parts Used:
WP3148952
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
could not control the temp of the element
take off back panel, simply unplug the old switch and plug in the new one. Simple
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from HARMONY, MN
Parts Used:
WPW10181986
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rosalind from APOLLO, PA
Parts Used:
WPW10181986
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MICHAEL from FOUNTAIN INN, SC
Parts Used:
WP3148952
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandeep from EDINA, MN
Parts Used:
W10777162
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from APACHE JCT, AZ
Parts Used:
WPW10308477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven Elementwas burnt into
Watched the video and did as shown
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Johnie from PARKERSBURG, WV
Parts Used:
WPW10308477
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven would not heat up.
Unplugged the range. Opened the oven door and took out the shelves. Took the right screw out, but had trouble getting the left one out do to the age of the range. Unhooked the two wires and took the element out. Put the new one in and hooked up the two wires. Attached the two screws and checked to see that the element laid flat and then tighten screws. Closed the door and plugged the range back in and turned the oven on and it worked perfect.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PHILIP from NORTH PORT, FL
Parts Used:
W10856603
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jenny from GREENFIELD, IN
Parts Used:
WPW10308477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the AER5823XCW1
61 - 75 of 185