AER5844VCB0 Amana Range - Instructions

the hardest part was moving stove to trplace part

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

After identifying the part and taking delivery of it, I opened the breaker for the unit and then removed the range top by taking out 2 Phillips screws and lifting the part away from the hinges in the back. The element was attached with only 2 spring loaded clips which I then removed, noting the numbered position of each. I then photographed the wiring (x4) from several angles and removed each of them. I attached the clips to the new element and reconnected the wiring to the main heating element and the sensor per the photographs. The element was then re-positioned into its mounting slots, the range cover was reattached with the screws and the unit tested once power was restored.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.

Open door 1/4 an slide the little latches on each hinge toward you. This will lock them in place. Close the door a little and lift it up. The door will slide out. Lay it face down on a table and undo all the screws. Do not remove the glass, frame etc. Slide old hinge out and new one in being careful not to slide the glass and frame out of alignment. It is a pain to get it all back together if you take every part out. Just do the hinges. Screw it back together. Reverse the door removal process by lowering the hinges into the oven receiver from a 75% closed position. Once in place, open the oven about halfway and slide the locks forward. This will allow the door to close completely. Note: Three hinges came with my set. Not sure what the third odd one is for.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.