ACS3350AS0 Amana Range - Instructions

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.

Shut off electric power. Removed bottom drawer.
Removed metal covers over burner in oven.
Removed 3 screws holding igniter in place. Disconnected wire plug under oven and pulled thru hole where igniter had been. Removed metal shield from defective igniter. Used care to place it on new igniter. Reinstalled everything.
My wife was observing and made me scrub under stove since I had the drawer removed.
I found the other repair stories very helpful in diaignosing my problem and ordering the right part. I ordered on Monday and received Wednesday afternoon normal delivery. Very good service.

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

remove oven flare pan in bottom of stove, about 25 screws, lift out and remove igniter. tip stove back and remove splash pan from underneath, 2 screws, unplug ignitor and reinstall using reverse procedure. igniter is very fragile so be extremely careful with it. reuse old hardware to hold in place,reassemble and good to go.

First, i removed all of the oven parts that needed to come out in order for me to remove the ignitor. Second, removed the manifold and the old oven ignitor. Then, i checked for 120 volts going to the ignitor. Replaced the ignitor with the new one and reassembled all of my oven parts. 15 mins top, but of course it may take a little longer for those of you who are not elecrically and mechanically inclined. Very east to repair.

This is the second igniter I've had to install in the last 2 years. First time the repair was done by the company I bought the range from. $35. part/ 140. labor. I watched the repairman do the job. It is literally one nut, three screws, and an electrical plug and socket. Here's the interesting part of the story: the appliance store would NOT sell the part to me. They insisted on installing it themselves. NOT FOR $140. Thanks for your help, great and easy to use website. I spent the $140. I saved of golf. Thanks again!

Pulled the burner cover, removed two screws holding igniter in place, pulled oven out from wall and unplugged igniter at back, feed wire and plug back thru to oven. Removed old igniter from holder slid new one in place and reversed procedure to feed wires back thru to back side. Plugged in igniter replaced burner cover and pushed stove back into place. The procedure took about five minutes if that.

Removed racks and pans from oven, removed 1 screw that housed the v shaped burner cover. Then I noticed the Igniter housing was held to back of oven with 3 small screws, removed 3 screws, and noticed the igniter just slid into the housing, but the connection would not come through back of unit. pulled out the lower tray to expose the underside of the oven and noticed 2 screws holding a metal cover, removed those and noticed connection to igniter, undid the connection, slid out the igniter and then just reversed the process to put back. It took me about 20 minutes, and that was only because I was being overly careful with the ceramic igniter, as the one in there just crumbled. Very easy job for anyone with even moderate skills. Ordered my part with assitance from a lady at parts express on Monday at noon, had the part delivered Tuesday at 3:00, had the oven back up and running fine by 3:30. Couldn't be happier, as this happened once before and the repairman charged me $185, this cost $48 and 15 minutes.
Unbelievable service and detailed help. I have this site bookmarked for anything moving forward.
Thanks

My husband took it apart then showed me how to put it back together. So I placed it in the metal holder and attatched all the screws.

I first diagnosed the problem with an ammeter, after I was sure of the problem I ordered the part and it came in 1 day early. When the part arrived I removed 12 screws to access the old part, unplugged it, plugged in the new one. The easiest way to save $150.00 I've managed.

basicly just replaced the element by unplugging the connector and removing the three screw that hold the element. easy process.