ACS3350AS0 Amana Range - Instructions

Remove the cover over the burner, two screws at the rear, this exposes the burner tube cover, one nut at the center. Three screws will remove the holder for the igniter. I had to remove a sheet metal cover underneath the oven( pull the drawer out) to gain access to the plug for the igniter. A good tip on this is the same valve controls the broiler and the oven, if one works and the other doesn't, it's the igniter. If neither works the gas vale may be the problem.

Replacing the igniter itself was a simple matter a few screws holding its housing and then plugging the new one into the connector. Difficulty came trying to figure out how to access the igniter. Disassembling the floor of the oven was a dead end involving many screws. Pulling the unit out from the wall was a big job and another failure. The problem was solved with the removal of the drawer. Underneath, in the rear was a sheet metal plate held by 2 screws. Behind that hung the igniter connection. Voila! Job done.

Took bottom oven pan off accessed through oven storage drawer.Removed a few screws holding the igniter bracket,removed igniter from its holder(Be really,really careful doing this procedure because the igniter tip is verrrrry fragile,ask me how I know)Put it all back together and Voila,it works!This is so easy a job a caveman can do it! Good luck!

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Easily replaced the stovetop burner bowls by removing the old ones and replacing with the new ones.

Parts Select provided easy online ordering and was nearly one-half the price of other online suppliers.The quality was excellent!

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Installed new igniter - easy job. Remove burner deflector, remove screws holding igniter bracket, remove panels below oven (accessible via removal of drawer), disconnect igniter and remove. Remove igniter from bracket, slide new one into bracket and reverse the steps to install it. Unfortunately, it didn't work. Igniter not glowing. I checked continuity on the igniter and it showed 90ohms resistance, so seems to be OK. Put multimeter on range plug end, turned on oven and multimeter did show cycling voltage at the plug (although I'm not certain what it should read). Relay in the control board does 'click' when oven turned on, so it also seems to work. Think I may be down to the gas control safety valve for the oven, but it is no longer available. Anyone have any other ideas? Hate to buy another igniter and have it still not work. Thanks!!

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

Removed old ignightor and installed new one

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I tested the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.

I have an older model gas oven which required that all screws had to be removed. With a screw gun the job would not haven taken long. Once the bottom pan was removed the oven ignitor took some finese to remove. This was only due to the short wires. Once pulled sufficiently to be able to disconnect the ignitior (although I was afraid I was going to pull the wires and separate them from the stove), it was very simple to unplug and plug in the new one (again, making sure to hold the plug so the wires would not retract back behind the wall which would have required the stove to be pulled out from the wall and the back disassembled).

The good news, it was a success and the oven works like new. Roughly $38.00 later, I am back cooking. The extra effort for the screws was offset by being able to complete this by myself and saving the cost of a repair man. Would do it again.

First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer back in the stove and turned on the over to see if it would light. Bingo, job done!

I removed the oven door by removing two screws, one above each hinge. With the door screws removed, position the door to the slightly open position and lift strength up to remove. Remove wire racks and the cover from the bottom of the oven. Remove the heat deflector which is held on with a single nut. Remove the screws that hold the cavity that houses the igniter and the burner. The igniter is held in place by a protective bracket that has to be reused. I slid the old igniter out of the protective bracket and then removed the cavity by allowing the burner and igniter to exit through an opening in the rear of the cavity. The drawer (broiler pan storage) had to be removed to remove the two screws to an access panel that allowed access to the igniter connector. After disconnecting the old igniter, I fished the new igniter connector through the back of the oven to connect it. I use masking tape to hold the access panel in place while reinserting and tightening the two screws. Replace the cavity that houses the igniter and burner. Slide the protective cover over the igniter. Realign and secure the burn and igniter assembly by reinserting and tightening the necessary screws. Reinserting and tighten the screws around the igniter/burner cavity. Replace the heat deflector by tightening the nut. Replace the cover that covers the bottom of the oven and the wire racks. Reinsert the drawer. Slide the door over the hinges and reinsert and tighten the two screws.