ALY2280BDS12 Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pauline from Weedsport, NY
- Parts Used:
- 74003106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven rack missing
Opened oven door, slid in rack , closed door...
Fit perfect....
Fit perfect....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SEARCY, AR
- Parts Used:
- 74003944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Inside Of Knob Busted Out, Would Not Turn Ignitor.
Actually too simply to list as diy job. Merely remove old knob and push new one onto spindle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Lufkin, TX
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lack of burner gas ignition
I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.
Thank You Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nataly from Brooklyn, NY
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of four burners did not start (no sparks)
Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- julie from harrodsburg, KY
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the burner cap on my maytag gas range was rusty on the inside and didn't allow the cap to sit flush-causing gas and flames to leak from under the cap
installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Santa Maria, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Igniter insulation had cracked and spark was shorting out on the flame holder whatchmacallit.
The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alberto from Houston, TX
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were rusted and rotten from the bottom, flames were coming from around the bottom
all i did was twist the burner counter-clockwise unplug 2 wires and installed the new ones, real easy, it took me about 7-8 minutes for the 4 burners, that was all, our stove is working like new now, albert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marty from Kennesaw, GA
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Replaced igniter in right rear burner
Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Mission, TX
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
rusted out burner on stove top
turned burner counterclockwise and removed it reversed procedure and installed new one..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brady from CARYVILLE, FL
- Parts Used:
- 74003944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
igniter knob for gas stove stripped out
Slip old knob off slide new knob on, be sure to align knob properly your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Appleton, ME
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner heads were rusted out, releasing flames from underneath and also clogged with carbon dust
Very simple! Unscrewed the burner heads with a simple twist, unplugged the two wires from the old head, plugged them into the new one, then screwed that back in. The flames are MUCH better - more efficient and safe. thank you! ( Only issue was when we ordered we didn't see a choice of color and the new ones are different, but it really doesn't matter on an older stove anyway.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CHESTER, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
replace igniters
Watched u tube video as supplied and followed instructions. Had trouble getting burners off so cleaned around edge of burners with fine bladed knife as suggested by other forum user and used oil filter type wrench to remove burner. There are three bumps on burner that hold it in place so need to turn anti clockwise to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from tisbury, MA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap had rusted out
It was pretty much a plug it in job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendi from Cypress, CA
- Parts Used:
- 74003106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed an additional rack for our RV oven
After some research in finding the information under the range hood, I did internet searches to find the appropriate replacement rack.
It fits great and we are thrilled to have the additional rack.
It fits great and we are thrilled to have the additional rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Albuquerque, NM
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One burner was sparking but not lighting
I first switched the old burner to a new position and different ignitor wiring. The problem persisted in both places, so I bought a new burner assembly and now the burner lights immediately. Very happy and a very simple replacement.
Was this instruction helpful to you?
Thank you for voting!