FDU2492WW (P1130626N) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Russ from Milford, NE
- Parts Used:
- R0706011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
hinge broken again
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randall from sheboygan, WI
- Parts Used:
- WPY0061732
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broiler coil burned out
removed back plate screw, removed two broiler screws. Disconnected wires in back plate by sliding them off of connectors. removed broiler coil and assembly. Using pliers, bent retaining hooks off of old coil, removed it and replaced it with the new coil. Reversed process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Pocomoke City, MD
- Parts Used:
- 31715901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door gasket gotten hard
I took oven door apart and replaced old gasket with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mountain Ranch, CA
- Parts Used:
- R0706010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge broken
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from portland, OR
- Parts Used:
- WP74011278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
oven light replacement
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Villa Ridge, MO
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vincent from Martinsville, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
electric surface unit not working
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from West Des Moines, IA
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Kasson, MN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface burner block corroded
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James J from Sweet Grass, MT
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Blocks were broken
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Staunton, IL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail M from Lockport, NY
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner was slow heating at times. Moved back burner to front still same thing.
Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cody from Abilene, TX
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface Burner not working
I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Cool, CA
- Parts Used:
- WP77001096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the element burnd true and I could not use the oven
A frind (my husband has ALZ> came over before I ordered the part lookt at it took it out and told me what to do. I ordered the part and got it in 3 day's Wonderfull.My friend came the next day and put it back in. I cleaned the oven the next day and I am back in action THank you so much for the great service P v. d. B
Was this instruction helpful to you?
Thank you for voting!