ARG7302WW (P1143337NWW) Amana Range - Instructions

Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.

Thanks PartSelect.com

1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.

It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and lift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.

looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove.
Needed flashlight to see under stove.

After a standard trouble shoot, and finding the control PCB has the correct line voltage and the unit failure has more than one function failure with-in the unit operation, I replaced the Control PCB.
Removal and install took about 10 min, and the unit works fine, all automation is working properly.
Lance

Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall

Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.

I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I tested the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.

I used your instructions

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Replaced glow bar/ igniter.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!