AER5722BAS Amana Range - Instructions

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Turned off breaker, moved unit and unplugged the unit. Safety first! Removed the oven door, removed two Phillips screws, pulled out the heating element, removed two clips.

Installed new element in reverse order. Put back the door. Plugged in unit, moved back into place and turned on breaker. Tested the oven, and it worked great. Maybe 20 mins total, very easy and saved at least 200 bucks vs calling a repair guy.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

My daughter repaired it without any problems.

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Simple Removed the broken element,put the new one in.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted