ARG7600LL (P1141298NLL) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Keith from Denver, CO
- Parts Used:
- WP31940001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven wouldn't ignite
Bought new igniter based on advice from other stories here. Didn't test the impedance. The igniter glowed, but the oven wouldn't start.
1. Removed single nut on flame pan & remove pan.
2. Removed Pan drawer and disconnected plug to igniter.
3. Removed 3 screws holding igniter in place.
Note: the screws were corroded & one stripped in removal - you may want to purchase the metal housing for the igniter assuming it comes with new screws.
4. Put everthing back in opposite order.
1. Removed single nut on flame pan & remove pan.
2. Removed Pan drawer and disconnected plug to igniter.
3. Removed 3 screws holding igniter in place.
Note: the screws were corroded & one stripped in removal - you may want to purchase the metal housing for the igniter assuming it comes with new screws.
4. Put everthing back in opposite order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Bonney Lake, WA
- Parts Used:
- WP31940001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Igniter was not turning on. This part fixed it.
Get to the ignitor:
Open oven, clean out the crude, and remove the bottom pan to get to the gas parts.
Remove the nut to get the flame sheild off.
Remove screws that hold the ignitor.
I stripped one and had to pry it off with a strait slot screw driver while turning it with a phillips.
Unplugging the ignitor:
Pull out the drawer. Removed the 2 panels under the stove to access the ignitor plug.
Replace the ignitor and reverse the procedure.
I did remove about 20 screws and the main pan at the bottom of the inside of the oven, but it didn't help me do anything, so don't make the mistake that i made with that.
Open oven, clean out the crude, and remove the bottom pan to get to the gas parts.
Remove the nut to get the flame sheild off.
Remove screws that hold the ignitor.
I stripped one and had to pry it off with a strait slot screw driver while turning it with a phillips.
Unplugging the ignitor:
Pull out the drawer. Removed the 2 panels under the stove to access the ignitor plug.
Replace the ignitor and reverse the procedure.
I did remove about 20 screws and the main pan at the bottom of the inside of the oven, but it didn't help me do anything, so don't make the mistake that i made with that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Uday from Ann Arbor, MI
- Parts Used:
- Y0309074
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked inside glass window of oven door
1. Slide the Oven door out of its hinges after removing the screws - see Owner's manual.
2. Place door on floor with the inside face on the floor.
3. Remove screws on side and bottom of door and the lift away the side stamped pieces.
4. Remove screws as they becom visible and lift away the pieces till you reach the inside glass.
Remember the sequence and be careful not to strip the Phillips screws when unscrewing.
2. Place door on floor with the inside face on the floor.
3. Remove screws on side and bottom of door and the lift away the side stamped pieces.
4. Remove screws as they becom visible and lift away the pieces till you reach the inside glass.
Remember the sequence and be careful not to strip the Phillips screws when unscrewing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Pleasanton, CA
- Parts Used:
- R0706011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rivet broke on the right side oven door hinge
Regarding my right side oven door hinge replacement, P/N PS2172201
After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.
Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.
Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.
Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.
Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Buffalo, MN
- Parts Used:
- WP31940001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Oven would not light
Unplug oven cord from wall receptical,
Remove bottom drawer from oven,
Remove sheet metal plate from rear of oven to gain access to the ignighter connection,
Disconnect old ignighter connection,
Removed the pan on the bottom of the inside of the oven,
Removed the hex nut on the top of baffle plate
Remove baffle plate,
Remove (2) screws holding ignighter in place,
Replace the ignighter and all other commponnents in reverse order
Remove bottom drawer from oven,
Remove sheet metal plate from rear of oven to gain access to the ignighter connection,
Disconnect old ignighter connection,
Removed the pan on the bottom of the inside of the oven,
Removed the hex nut on the top of baffle plate
Remove baffle plate,
Remove (2) screws holding ignighter in place,
Replace the ignighter and all other commponnents in reverse order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from carol stream, IL
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat up, but everything else worked, broiler and gass range
was so each, we removed the door and the racks. and the bottom drawer out. All we had to do was remove the ignitor that was held in wtih screws we could read the wires from the bottom of the oven and then put the new one in and attached the wires from the bottom. We had read reviews of others that did the same repair and were confident that we could do it because they described it and said it was so easy. Thanks everyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from wyandotte, MI
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
my oven took for ever to light after a while it didn't
i disconnected the power supply, took all shelves out of oven, removed screw that holds the bunner to oven, removed bunner along with igniter. cut wires to igniter wired new igniter , tested before
installing bunner,( ok) installed bunner and screw
fired up and all is well.
installing bunner,( ok) installed bunner and screw
fired up and all is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemarie from Huntington, NY
- Parts Used:
- Y0315769, WP7504P109-60
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Ignitor couldn't be removed because the screws were ruined.
This is the second time I have had to call a repair person to GE the old screws off. It isn't the fault of the part. Better original screws would have helped. It was very frustrating an expensive. I would say check the screws before you order the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAN from HOFFMAN ESTATES, IL
- Parts Used:
- WP7504P109-60, 315841L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
stove's Plastic end cap was cracked, burner head worn out.
Investigated the stove top and found worn part under stove top burner. Looked up defective/worn out part on line at Parts Select web site. Ordered on line and in a few days had a box sent with new part and replaced it. The repair time was 25 minutes or so. Part began to work properly. Plastic end cap was also swapped for a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Malcolm from Corona, CA
- Parts Used:
- WP31940001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven burner not lighting
After reading previous posts regarding this type of problem, I determined the very high likelyhood that the over ignitor needed to be replaced. Accessing the underneath of the oven compartment, I removed the metal shield covering the ignitor wires in order to unplug the ignitor. (Be sure to disconnect power cord first)
From inside of the oven compartment remove the flame spreader plate ( 1-screw) which gives access to the ignitor. Remove the three screws holding the ignitor bracket and pull the wire and plug through. That's it !!
Installation of the new ignitor is the reverse of the above proceedure.
Oven now functions normally again.
A very simple repair.
From inside of the oven compartment remove the flame spreader plate ( 1-screw) which gives access to the ignitor. Remove the three screws holding the ignitor bracket and pull the wire and plug through. That's it !!
Installation of the new ignitor is the reverse of the above proceedure.
Oven now functions normally again.
A very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Seattle, WA
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burners would not autolight, had to be lit with match
This was VERY easy and I've never worked on this type of appliance before.
First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).
Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.
once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.
Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.
First, take off the grate, thermal plate, etc that are resting on top of the stove (this is all the stuff you take off to clean the stovetop).
Then, carefully unscrew the two screws holding the burner to the gas pipe. Grab the screws and set them aside so they don't fall back into the stove, then pick the burner up off the stove.
once you have the burner a few inches above the stove surface, wiggle off the single wire by grabbing it on the metal part (not by the wire) and gently wiggling it off.
Grab new burner, push on wire and sit it on stove, use a finger in the gas pipe to align it and put the two screws in. you're done.
Was this instruction helpful to you?
Thank you for voting!
One hinge was broken and the other was Sprung
Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramon from Little Falls, NJ
- Parts Used:
- 786324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broiler Igniter failed
Had to take entire back panel off, to disconnect wiring. Once disconnected, removed two screws holding up igniter in oven. Pulled it through and removed from holder, Be careful new igniter very fragile. Reconnected, put panel back on, then turn on to verify, all went well, fully operational.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dion from grayslake, IL
- Parts Used:
- WP31940001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would light only after 15 to 30 minutes
opened up the oven to locate the position of igniter
disconnected igniter and checked the continuity of the igniter to find that I had an open circuit
once I found out the igniter was no good I google for appliance parts and found parts select had the best prices that I could find. I called a couple local parts stores and there prices were definately inflated. I chose to go with parts.select.com
I receive the part in two days! I installed the new part within 15 minutes and turn on the oven to have it light almost instantly. I won much praise from my wife. Parts.select.com recieves my praise for ease and quickness of part delivery.
disconnected igniter and checked the continuity of the igniter to find that I had an open circuit
once I found out the igniter was no good I google for appliance parts and found parts select had the best prices that I could find. I called a couple local parts stores and there prices were definately inflated. I chose to go with parts.select.com
I receive the part in two days! I installed the new part within 15 minutes and turn on the oven to have it light almost instantly. I won much praise from my wife. Parts.select.com recieves my praise for ease and quickness of part delivery.
Was this instruction helpful to you?
Thank you for voting!