PHU186NWW (P1131811N) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nelson from Selden, NY
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven gas flash, igniter not heating up enough
Removed old igniter held by one bolt & nut, diconected two leads to igniter. Gas mainifold remained in place during repair. Replaced with new igniter, using old mounting bracket and wire ties. Total repair time 30min, oven repair service wanted to charge $80 just for diagnosis. Total cost of repair doing it myself was $50.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Milford, NE
- Parts Used:
- R0706011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
hinge broken again
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Pocomoke City, MD
- Parts Used:
- 31715901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door gasket gotten hard
I took oven door apart and replaced old gasket with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mountain Ranch, CA
- Parts Used:
- R0706010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge broken
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffry from Sussex, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven no longer came on
Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VICTOR from MOUNT PROSPECT, IL
- Parts Used:
- 786324
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Screws Were Rust6Ed, Melted
Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from portland, OR
- Parts Used:
- WP74011278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
oven light replacement
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Columbus, GA
- Parts Used:
- 1430322
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front burners would not light.
First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willliam from Goldfield, IA
- Parts Used:
- WPY0314907
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gears and gear box top case cracked
Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fletcher from Greenville, SC
- Parts Used:
- 786324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ignitor would not ignite the oven
Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from Florence, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old igniter lost power to ignite gas..
The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Quincy, FL
- Parts Used:
- WPY0307363
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter replacement
Removed grill cover, took out old filter and placed new filter, placed grill back over filter. Back in business!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from UKIAH, CA
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from Norman, OK
- Parts Used:
- WPY0314907
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven not heating, F3 trouble code.
Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.
Was this instruction helpful to you?
Thank you for voting!