ARG7102C (P1143389N C) Amana Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

Removed racks and pans from oven, removed 1 screw that housed the v shaped burner cover. Then I noticed the Igniter housing was held to back of oven with 3 small screws, removed 3 screws, and noticed the igniter just slid into the housing, but the connection would not come through back of unit. pulled out the lower tray to expose the underside of the oven and noticed 2 screws holding a metal cover, removed those and noticed connection to igniter, undid the connection, slid out the igniter and then just reversed the process to put back. It took me about 20 minutes, and that was only because I was being overly careful with the ceramic igniter, as the one in there just crumbled. Very easy job for anyone with even moderate skills. Ordered my part with assitance from a lady at parts express on Monday at noon, had the part delivered Tuesday at 3:00, had the oven back up and running fine by 3:30. Couldn't be happier, as this happened once before and the repairman charged me $185, this cost $48 and 15 minutes.
Unbelievable service and detailed help. I have this site bookmarked for anything moving forward.
Thanks

My husband did the repair. He removed the wires and screws from the element and replaced with new part.

Shut off electric power. Removed bottom drawer.
Removed metal covers over burner in oven.
Removed 3 screws holding igniter in place. Disconnected wire plug under oven and pulled thru hole where igniter had been. Removed metal shield from defective igniter. Used care to place it on new igniter. Reinstalled everything.
My wife was observing and made me scrub under stove since I had the drawer removed.
I found the other repair stories very helpful in diaignosing my problem and ordering the right part. I ordered on Monday and received Wednesday afternoon normal delivery. Very good service.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

this was the second one replaced in 5years,they don't make things like they used to

1. Disconnect oven electric supply.
2. Remove oven door (2 screws).
3. Remove inside-oven bottom plate (slide forward, lift).
4. Remove inside-oven burner cover (1 nut).
5. Disconnect igniter enclosure (3 screws).
6. Remove under-oven drawer (slides out).
7. Remove panel at back of oven in under-oven compartment to access igniter electrical connection (2 screws).
8. Disconnect old igniter.
9. Extract old igniter from igniter enclosure. (Don't use much force; just slightly expand the metal flanges of the enclosure.)
10. Dispose of old (bad) igniter.
11. Insert new igniter into igniter enclosure.
12. Place igniter enclosure in oven compartment and slide electrical connector through to back/lower compartment.
13. Connect new igniter in under-oven compartment.
14. Replace panel at back of oven in under-oven compartment (2 screws).
15. Replace igniter enclosure (3 screws).
16. Replace inside-oven burner cover (1 nut).
17. Replace inside-oven lower plate.
18. Replace oven door (1 screws).
19. Reconnect electric supply.

The oven door had a stripped thread so I took a knife and held up on washer and unscrewed it. I unplugged the oven. Then slide door off. Then removed pan in oven, then used socket wrench to take off burner sheild (reflector). Then You take out bottom drawer, in the back of opening there is a cover over the connections 2 screws. I unpluged the igniter. Now back in oven the igniter has a cage with 3 screws.. the screw was rusted and frozen. Needed to use WD40 on the screw and let set 10 mins. Now I could remove that screw and other 2 screws. With the cage off I was able to go to bottom where the drawer was and reach in and pull igniter completely out. Becareful not to break the anode it is fragle. ( the black piece) Then reverse and put the new one in. I actually swaped some of the rusty screws that gave me trouble with other screws in the oven that were the same, in case I have to do this again some time in the future. These previous comments from people were greatfully helpful!!!! Thank you!!!

Replaced the igniter. With the new igniter, the gas came on when the oven was turned on and lit with no problem.

Removed covers. Unplugged and unscrewed oven igniter mounting screws. Pulled out failed igniter and slid in new igniter. Installed igniter in reverse order.

TIP: Many igniters will test correctly with meters. This is due to they will fail under a load (when in use) in the oven. But when testing with the meter they will test ok because they are not being put under the stress of use in the oven.