AGR5725RDS16 Amana Range - Instructions

First I changed the temperature sensor and when it didn’t get hot I Also changed the igniter. Fired right up.

I unscrewed the ignitor from the gas supply. Unplugged the ignitor. Plugged the new ignitor in and screwed it back in place to the gas supply. It could not have been easier!

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !

I didn't. Don't know how to get to light bulb to change it for this specific model

So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

popped out the old one with a screwdriver discconnected two wires, reconnected the wires to the new rocker sitch and popped in the new one..

Took the old levelling leg out and screw the new one in.

it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks

Replace the igniter. Removed 2 rear screws that secure bottom oven pan. Removed pan. Ignigter is located in center rear by 2 screws. Removed the screws and pulled ignigter out from rear. There us a prong connection that when pressed will release igniter. Don't touch new ignigter without gloves on. Will reduce life. Plugged in new ignigter and secured w 2 screws. Turned on oven to ensure problem was fixed. After 30 seconds, oven ignited. Replaced bottom oven pan. Tadaa!

First i turned off the gas and unpluged the electric to the stove. I removed the gas line and the screws that held the housing of the hood and valve assembly .Then i unplug 4 wires that operated the safety valveon the gas.Unthreaded 2 lines ,one for the oven and the other one for the boiler.I then replace the new hood and valve kit and put everything back together and the oven works just fine.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.