ARG7302CC (P1143391NCC) Amana Range - Instructions

My husband did the repair. He removed the wires and screws from the element and replaced with new part.

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

Thanks to previous reviews it was really easy! Popped cover plate off bottom of oven. Removed diffuser plate by using socket wrench to remove one bolt. Removed three screws (one on top; two on left side) of bracket. Good idea to use a magnetic screwdriver so they don't get lost! Slid igniter out of bracket- a bit tricky but gently eased it out. Slid new igniter in place taking care not to touch the element. Dropped wires and harness down next to old ones. Removed bottom drawer, crawled under and switched connections. Put everything back together. It did take a little longer for the new igniter to start the first time- about one minute- but now fires right up.

Part arrive only a couple of days after ordering, and installation time was less than to schedule a repairman! My only regret is that I didn't send my better half off for the entire afternoon so I could really make it out to be a big deal as my brother-in-law, the appliance repairman, made it out to be!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

1.) Trun Off Power
2.) Remove the Storage Drawer and the two (2) screws holding on the (Ignitor Plug) access cover-plate located in the back of the storage drawer access. (see page 15 if same model)
3.) Dissconnect the Ignitor Plug
4.) From the oven opening remove the three screws holding the Ignitor Holder.
5.) Remove the Ignitor and Holder from the oven by gently guiding the wires through the access hole
6.) Pull the Ignitor from the holder
7.) All Ignitors are extremelt fragile; install the new Ignitor into the Holder and make certain it is installed tight, mine was not. (Slight bending with my thumbs on the 1/4" flanges might hold it tighter if it is lose.)
8.)Reverse the process.
Note: One person here said they removed "ALL" the screws, maybe it was a different model, I only had to remove a total of "5" screws, two at the access cover plate and three at the Ignitor holder.
First time took me 20 minutes, if I needed to do it today, maybe 10.
Please also note that I didn't troubleshoot the Ignitor, as I didn't have a wrap-around amp meter, but the typical problem here would be the Ignitor, not the Gas Valve. Good Luck, pt

Removed the bottom drawer then removed the door - 2 screws. It would be hard to reach in oven with door still attached and it is simple to remove and put back on. Removed the racks and pan on bottom, which just lifts out. Removed 3 screws that hold bracket that contains igniter. The igniter plugs in and to access the plug you must remove a cover underneath the range. Once the drawer is out you have to crawl back in there to access the plug. I sent in my 14 year old for that. Make sure range is unplugged. Insert igniter in bracket and feed wire back down to plug in and reattach. Vacuumed oven out with a shop vac, etc. and it is a 30 min project.

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

1. Disconnect oven electric supply.
2. Remove oven door (2 screws).
3. Remove inside-oven bottom plate (slide forward, lift).
4. Remove inside-oven burner cover (1 nut).
5. Disconnect igniter enclosure (3 screws).
6. Remove under-oven drawer (slides out).
7. Remove panel at back of oven in under-oven compartment to access igniter electrical connection (2 screws).
8. Disconnect old igniter.
9. Extract old igniter from igniter enclosure. (Don't use much force; just slightly expand the metal flanges of the enclosure.)
10. Dispose of old (bad) igniter.
11. Insert new igniter into igniter enclosure.
12. Place igniter enclosure in oven compartment and slide electrical connector through to back/lower compartment.
13. Connect new igniter in under-oven compartment.
14. Replace panel at back of oven in under-oven compartment (2 screws).
15. Replace igniter enclosure (3 screws).
16. Replace inside-oven burner cover (1 nut).
17. Replace inside-oven lower plate.
18. Replace oven door (1 screws).
19. Reconnect electric supply.

this was the second one replaced in 5years,they don't make things like they used to

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

I identified the igniter problem in the lower part of the oven by turning the upper broiler on and finding that it worked. I then knew it was not a gas supply problem. Replacing the igniter required removing the two oven racks, removing the drip pan, removing two screws that connect the igniter to its mount and disconnecting the wires in the back of the oven. The install was the reverse of removal. One tip, on my oven I was able to lift the oven door off of its hinges which allowed much easier access to the igniter.

Pulled the burner cover, removed two screws holding igniter in place, pulled oven out from wall and unplugged igniter at back, feed wire and plug back thru to oven. Removed old igniter from holder slid new one in place and reversed procedure to feed wires back thru to back side. Plugged in igniter replaced burner cover and pushed stove back into place. The procedure took about five minutes if that.

After removing the oven shelves, the burner cover came right up. The ignitor was in plain sight, and after removing the screws I pulled it straight out so I could get to the wire nuts. After swapping out the old igniter and sliding the cover over the new ignitor, the new piece slipped back into place in the oven. The screws were put back in, and the burner cover and shelves put back, and the oven works wonderfully again.