ACF3375AC (PACF3375AC2) Amana Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.

I first tested the broiler and that worked so we determined that the igniter on the bottom was not working. I removed the grill and then removed the igniter ( it is attached with two screws and unplugs from the back of the oven. I then looked up the part we needed on the part select website by model number and found the exact one ( the picture was very helpful) We received the part in one day installed it and the oven is working better than ever.

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

Followed instructions, those were OK.
Dishwasher front still leaking

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

The biggest problem was gettng the correct ignitor, seems there are two. The first ignitor was the wrong one (I do not remember seeing any reference to which on the order page), but once I had the correct one my biggest issue was to get the stove out far enough for me to get behind it to take the cover off. Six scews and a disconnect and a repeat to replace and done. I must mention that the service rep was extremely helpful and easy to deal with and there was no language issue. The replacement part came in two days. I would definitely order more parts from this company

Removed plate at bottom of oven and unscrewed ignitor. Tipped oven forward and removed tiny back panel to reach plastic socket that disconnected ignitor from oven. Pulled ignitor out and awaited replacement part and did reverse steps. Oven ignitor worked right away.

For stovetop I ordered part and removed sheet metal screws from oven rear top panel after appliance was pulled from wall, gas and electrical disconnected. I pulled old spark ignitor module out and transferred colored wires to new module and snapped that into place. Replaced oven and presto, stovetop ignitors worked immediately.

i got the right part from u fast del.and had it fixed in 15 min. was very happy withu service thank u will buy more parts from u when i need them it was the same part i took out

I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr

The burner has two screws holding it in place. I remover those and lifted the burner up. I then disconnected the wire attached to the igniter that was on the old burner and attached it to the igniter that was pre-installed on the new burner. I then placed the burner back into position and reinstalled the two screws. The reason that I bought the burner assembly is that I was unable to unscrew the screw underneath that held the igniter in place on the old burner.

The repair was easy. Used an ohm meter to find problem, if you follow wiring schematic , it is fairly easy to trace. Found open circuit across igniter. Repair was easy, only needed to remove part of back plate and bottom shel in oven and replace igniter, the repair took about 30minutes.

Took off the burner by unscrewing the two screws and lifting out the burner/igniter together being careful to not let the electrical connection come apart. If it does then you have to take all 4 burners off so you can lift the whole oven/burner top. Disconnect the old igniter by (more than likely) drilling out the old screw, if you are lucky maybe the old screw holding the igiter will actually unscrew. If not, you can put a new screw in to hold the new igniter, put it all back together and youre done.

Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.

I am sure I saved a bunch of money for an outside repair. It was so simple I was embarassed that I did not attempt the repair sooner. Removed two screws from old burner head lifted it up unplugged the electrode wire replaced with new burner head put the two screws back in place and I was finished.

The broiler igniter and oven igniter are the same - WITH ONE MPORTANT DIFFERENCE- the plug! I tried to just switch them since we dont ever use the broiler but could not, due to the plug. I think that is part of planned obsolescence ! Anyway, I left the door and the power on - you guessed it, rebel! If you get a tingle from replacing this part you shouldnt be trying to fix it on your own! I removed the oven racks, took two small screws from rear of oven floor out, removed base plate. Two more small screws released the defective part. Pulled the plug wire through the back of oven and unclipped the connector. Plugged new part in, tucked the wires back into the insulation, replaced two screws on the igniter. Test fired oven- worked like a champ. Shut burner off, reinstalled base plate and screws and put the oven racks back in. Easy!