CARDS801WW (P1131925NWW) Amana Range - Instructions

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Really easy!! Cut off Breaker so the Range had no power. Use phillips head screwdriver, remove the two screws holding the bake element in. Remove connectors from element. I put (heat shrink) wrap around the female connectors then attached them to the element, heated the shrink wrap, replaced the screws and cut on the breaker / power. Turned on the oven (350) to "bake" off the oil film off of the element. (Element will smoke / smell for a few minutes).

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

Repair was fast and easy 2 screws out 2 screws in. The best thing was I ordered the part Tues. morning and received it on Weds. To extra shipping charge!!! They were just that fast. Awesome Company!! Thanks!!

Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

Most difficult problem was locating and getting to the two screws one at each end of the cowling under the upper facias for the griddle and burner sections respectively . Once out , all knobs removed , the switch was accessed by pulling the cowling forward and up a couple inches . Noting the 3 small color coded wires locations and the two color coded power input wires for install of new switch . Balck sharpie touched up normal wear on cowl and facia panels .

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

I took oven door apart and replaced old gasket with new one.

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.

As others have described...removed old, replaced with new. Turning off electricity first, of course. Needed tweezers to pull wire out to front. Glad we could still get the part for the 20+ year oven. And we received it in 2 days. Thanks.

Cut off power to my range at the circuit breaker. Removed the 2 screws from the original element, pulled the element out about 4 inches to expose the wires to see the connections. (I put clothes pins on the wires to keep the wires from possibly sliding back into the holes in the oven.). Pulled the connections apart carefully, removed the old element, plugged in the new one, slid the wires back in the holes, replaced the 2 screws & was done! I did this by myself before my husband got home ... very easy! And I was thrilled to have my oven back!

A frind (my husband has ALZ> came over before I ordered the part lookt at it took it out and told me what to do. I ordered the part and got it in 3 day's Wonderfull.My friend came the next day and put it back in. I cleaned the oven the next day and I am back in action THank you so much for the great service P v. d. B

Removed grill cover, took out old filter and placed new filter, placed grill back over filter. Back in business!

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.