AGR5725RDQ16 Amana Range - Instructions

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

Found serial # as advised on web site. Found parts listing & ordered part. Got it in less than a week .
Unfastened two screws on top of door. Inserted glass. Applied a little mastic to prevent it from coming out again.
Done & done.
Do I get a prize ?

removed inside bottom of oven, removed 2 screws that held the ignighter, pulled out the oven, removed one screw on small cover, unpluged old ignighter, removed old ignighter, pusned the wires through the back of the oven, plugged ity in, attached the nerw ignighter, and replaced the cover/ and the bottom of the oven.
i teted the oven before i closed everything to insure it would light.

A friend helped me to fix it. First I removed the door from the oven itself. Next, we unscrewed the four screws from the glass holder at the bottom of the door and removed it. Next, we straightened out the glass holder, as it was slightly bent up from the front glass shattering. Next, we slid the glass into the door. Finally, we reinstalled the door to the oven. Voila! It was like brand new again.

Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

Remove door
Remove front cover of door
Remove hinge screws
Put back together.

Husband did repair. He removed the
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.

I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.

Check and see if power is going to the ignitor. Do an amp draw test on the ignitor. The gas valve will not open if it won't draw the right amount of current. Sometimes it will glow but wont be pulling the right amount of juice. In my case it wasn't even glowing but it still looked okay. The mounting screws can break or strip upon removal if they are old. In my case I had to drill a hole, for a new screw, on the back one, and the front one tried to strip out. I might try a little heat next time before removing them. If no power is going to the ignitor when you turn on the oven it might be that the board has gone bad. The ignitor should draw close to 3 amps.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

same as taking out old part and i misdiagnosed the problem ordered wrong part first and parts select steered me ito the correct part thank you

There are two elements to look at, one on top (broil) and one on the bottom (bake). Same element but may have different connectors. Double check before ordering.

The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand.
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly