AGS781LL (P1143306NLL) Amana Range - Instructions

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Daughter and family came to visit Gramps for the weekend; Saturday morning, arose and opened a couple of cans of grand buscuits. Set aside to let rise then turned oven on to preheat. Came back later and oven did not work. Stove top worked, broiler worked, but no oven. What to do, didn't want to waste dough; perhaps salvage for dumplings, no; make poorboy doughnuts, no; Aha, lets use the outside gas grill, never done it, worth the try, remember old camping days except using gas. Worked like a charm, crisis over. Now back to oven. Since everything worked except the oven burner problem could be in the igniter, or oven control. Removed covers to burner assembly, pulled igniter, checked for continuity across the two leads. No go. Wait, need to check oven control, placed voltmeter across incomming leads, turned oven controls on and had voltage. Conclusion, igniter bad. Also noticed a small rust hole in the burner tube next to igniter, not good. Went on-line to PartsSelect, entered make and model number. No model but gave choice close to model. Viewed pictures, found one that came close. Placed order. Parts came in a very short time. Matched new parts to old. perfect. Removed burner tube and installed new one, one screw, simple. Wire nut the incomming leads to igniter and install, three screws, simple. Turned oven on, igniter glows bright, gas comes on, good blue flame, no need to adjust air inlet vents on burner tube. Turned off oven, replaced covers, then turned on oven, baked cornbread and enjoyed. Thanks, back in business. Dave

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

First I removed the knobs on the range, then the front cover and then removed the two screws that hold each burner in place. I removed the top and removed the Module and started replacing the burners and front ocver and knobs. The Module worked GREAT. Thanks for your fast service in getting me the parts.

Unscrewed the burners,lifted the top up,unplugged the burners.Took out the bad module,making sure of where the wires went and put them in the same spots on the new module,reconnected the burners lowered the top screwed the burners back in and the burners lit.

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

Removed old ignightor and installed new one

Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.

removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.