ARRS6550E (P1143905N E) Amana Range - Instructions

Removed 2 phillips screws and pulled elements out 3 to 4 inches. One of the leads touched the housing and blew the circuit breaker, so don't forget to unplug or turn the breaker off! Simply slide clips off and install on new element. push back in place and reinstall 2 screws. Very simple.
P.S. element was delivered very fast!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly

Pretty simple. Turned off breaker. Lifted the top, cut the 2 wires. Going to the burner, put the 2 wire nuts on, and screwed the bracket in.

Turned off 230 volt breaker to range,connected old wires to new element ,put back into place replaced the two mounting screws. Turned breaker back on and tested range.

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.

removed back plate screw, removed two broiler screws. Disconnected wires in back plate by sliding them off of connectors. removed broiler coil and assembly. Using pliers, bent retaining hooks off of old coil, removed it and replaced it with the new coil. Reversed process.

turn the power off first, remove knobs, removed burners,disconnected wire from igniter,raise the top of the stove,re rmoved wire from the door lock removed two screws remove the door lock itself, then put all back on in same order as I remove. Main thing to remember is to writeyour colors of the wire down so you know where to replace them.

Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!

Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.