ACF3375AS (PACF3375AS0) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donella from Mount Horeb, WI
- Parts Used:
- WP7504P109-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner wouldn't light. Spark occuring below the burner head between it and the electrode.
Remove two phillips screws, lift the burner head up and remove the wire from the electrode. DO NOT DROP THE WIRE!!! It will fall into the stove top, adding much more time and frustration to this very simple repair. Reverse these steps to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Loxahatchee, FL
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not heating.
Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Lockport, IL
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat
Replaced both the broiler (top) oven ignitor and bake (bottom) oven ignitor! Easy to do, no need to call a repair person on this job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerard from Ashland, NH
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would heat
took the bottom of oven out.Took the ignitor off the bar. Took the center panel off of the back of stove. Unplugged the ignitor, plugged new one in. Attached ignitor to bar.Put bottom panel back in stove. all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dayton, OH
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner grate pads worn off or missing
I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Middleton, NH
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake oven would not start
The repair was easy. Used an ohm meter to find problem, if you follow wiring schematic , it is fairly easy to trace. Found open circuit across igniter. Repair was easy, only needed to remove part of back plate and bottom shel in oven and replace igniter, the repair took about 30minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hau from Burke, VA
- Parts Used:
- 31750717
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove Range Drawer Difficult to Open and Close
Insert one end of the railing into the slot in the back of the stove. Align the front end of the railing with the hole at the front of the stove. Align the roller with the hole. Secure the front end of the railing, roller ,and hole with the shoulder bolt using a 10mm wrench. Tighten just enough but don't over tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Manchester, NH
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven temp would not climb- burner would not fire- no error codes
The broiler igniter and oven igniter are the same - WITH ONE MPORTANT DIFFERENCE- the plug! I tried to just switch them since we dont ever use the broiler but could not, due to the plug. I think that is part of planned obsolescence ! Anyway, I left the door and the power on - you guessed it, rebel! If you get a tingle from replacing this part you shouldnt be trying to fix it on your own! I removed the oven racks, took two small screws from rear of oven floor out, removed base plate. Two more small screws released the defective part. Pulled the plug wire through the back of oven and unclipped the connector. Plugged new part in, tucked the wires back into the insulation, replaced two screws on the igniter. Test fired oven- worked like a champ. Shut burner off, reinstalled base plate and screws and put the oven racks back in. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geri from Brand Haven, MI
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the pads on the bottom of the grate kept falling off.
I was able to order the part I needed. The faulty pad had a broken stem.Several pads came in a bag so if I have the problem again I will have the parts on hand. I bought some RTV glue suitable for items at high temperatures; used a probe to make sure the hole in the grate was clear and clean and glued the new pad in place.
Was this instruction helpful to you?
Thank you for voting!