AGR5715QDB Amana Range - Instructions

Replace the igniter. Removed 2 rear screws that secure bottom oven pan. Removed pan. Ignigter is located in center rear by 2 screws. Removed the screws and pulled ignigter out from rear. There us a prong connection that when pressed will release igniter. Don't touch new ignigter without gloves on. Will reduce life. Plugged in new ignigter and secured w 2 screws. Turned on oven to ensure problem was fixed. After 30 seconds, oven ignited. Replaced bottom oven pan. Tadaa!

Took the old levelling leg out and screw the new one in.

popped out the old one with a screwdriver discconnected two wires, reconnected the wires to the new rocker sitch and popped in the new one..

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

It was really easy, just lift the door off from the range, I set it down on the box that the hinges came in, took the six screws out to release the front fascia of the door from the back, hinges are right there, un-screw and install the new hinges, put everything back together in reverse and lift the door back on to the range, less than 10 minutes!

Considered calling a repair facility, after reading your tips and what parts should fix what problem I decided to fix myself. Moved oven out,slide in gas range. Took off probe and tested with volt ohm meter, read 1090 ohms, should have been good. I could see oven igniter glow red, but I decided to replace both units, glad I did. Oven go's from 100' to 350' in 8 minutes now, for less than $85.00 have a fully functioning oven now. I'm sure the repair would have exceeded $300.00 or more being we live in a rural area. Thanks for the tips from your experts as well as you customers.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

First i turned off the gas and unpluged the electric to the stove. I removed the gas line and the screws that held the housing of the hood and valve assembly .Then i unplug 4 wires that operated the safety valveon the gas.Unthreaded 2 lines ,one for the oven and the other one for the boiler.I then replace the new hood and valve kit and put everything back together and the oven works just fine.

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

Removed oven door, removed bottom of oven, removed old igniter, installed the new one and plugged it in in the back of the stove. Installed oven door and it works fine. .

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

replaced heat sensor

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.