ARR620W1 (P1138601S) Amana Range - Instructions

Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.

My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!

I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.

replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).

left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge.
Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.

I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).

* * * *
I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)

This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

Top (broil) element broke in two on oven. Ordered part,it was there in three days. Quick fix, removed screw holding element to oven wall, unplugged wires, then just swaped out elements. Re-attached wires just as they were on old element and screwed back into same place and oven is working again.

Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

I unscrewed the 3 screws that held the element in place. My husband disconnected the back wired part of element .Then he reconnected new element wires and I rescrewed 3 screws in of new element. Very simple. I just wasn't sure about the back wired part, but like I said my husband seemed to know what he was doing so I let him do that part!

After I removed the piece of metal separating the two wires, I inserted the unit with no problem.

Simply removed the old heating element and plug the new element terminals into socket.

Went together real easy , but I poped a fuse/circuit braker.
The braker would not reset at first, but we got it all working fine.