ARG7301L (P1143324N L) Amana Range - Instructions

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

My husband did the repair. He removed the wires and screws from the element and replaced with new part.

Shut off electric power. Removed bottom drawer.
Removed metal covers over burner in oven.
Removed 3 screws holding igniter in place. Disconnected wire plug under oven and pulled thru hole where igniter had been. Removed metal shield from defective igniter. Used care to place it on new igniter. Reinstalled everything.
My wife was observing and made me scrub under stove since I had the drawer removed.
I found the other repair stories very helpful in diaignosing my problem and ordering the right part. I ordered on Monday and received Wednesday afternoon normal delivery. Very good service.

The oven door had a stripped thread so I took a knife and held up on washer and unscrewed it. I unplugged the oven. Then slide door off. Then removed pan in oven, then used socket wrench to take off burner sheild (reflector). Then You take out bottom drawer, in the back of opening there is a cover over the connections 2 screws. I unpluged the igniter. Now back in oven the igniter has a cage with 3 screws.. the screw was rusted and frozen. Needed to use WD40 on the screw and let set 10 mins. Now I could remove that screw and other 2 screws. With the cage off I was able to go to bottom where the drawer was and reach in and pull igniter completely out. Becareful not to break the anode it is fragle. ( the black piece) Then reverse and put the new one in. I actually swaped some of the rusty screws that gave me trouble with other screws in the oven that were the same, in case I have to do this again some time in the future. These previous comments from people were greatfully helpful!!!! Thank you!!!

Replaced the igniter. With the new igniter, the gas came on when the oven was turned on and lit with no problem.

remove oven flare pan in bottom of stove, about 25 screws, lift out and remove igniter. tip stove back and remove splash pan from underneath, 2 screws, unplug ignitor and reinstall using reverse procedure. igniter is very fragile so be extremely careful with it. reuse old hardware to hold in place,reassemble and good to go.

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

This is the second igniter I've had to install in the last 2 years. First time the repair was done by the company I bought the range from. $35. part/ 140. labor. I watched the repairman do the job. It is literally one nut, three screws, and an electrical plug and socket. Here's the interesting part of the story: the appliance store would NOT sell the part to me. They insisted on installing it themselves. NOT FOR $140. Thanks for your help, great and easy to use website. I spent the $140. I saved of golf. Thanks again!

Pulled the burner cover, removed two screws holding igniter in place, pulled oven out from wall and unplugged igniter at back, feed wire and plug back thru to oven. Removed old igniter from holder slid new one in place and reversed procedure to feed wires back thru to back side. Plugged in igniter replaced burner cover and pushed stove back into place. The procedure took about five minutes if that.

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.