ZRTC8500WW (P1143477NWW) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Sturgis, MI
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower Bake Element burned out
Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Milford, NE
- Parts Used:
- R0706011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
hinge broken again
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randall from sheboygan, WI
- Parts Used:
- WPY0061732
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
broiler coil burned out
removed back plate screw, removed two broiler screws. Disconnected wires in back plate by sliding them off of connectors. removed broiler coil and assembly. Using pliers, bent retaining hooks off of old coil, removed it and replaced it with the new coil. Reversed process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Gilford, NH
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking element overheated and split into two parts.
First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Madison, WI
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven heating element burnt out
The repair was simple, two screws and plug in and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mountain Ranch, CA
- Parts Used:
- R0706010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge broken
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from portland, OR
- Parts Used:
- WP74011278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
oven light replacement
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Fairport, NY
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burner wasn't light up.
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willliam from Goldfield, IA
- Parts Used:
- WPY0314907
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gears and gear box top case cracked
Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from cleveland, TX
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner Would,Nt Heat Up.
Removed top of stove replaced heating element ,piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hau from Burke, VA
- Parts Used:
- 31750717
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove Range Drawer Difficult to Open and Close
Insert one end of the railing into the slot in the back of the stove. Align the front end of the railing with the hole at the front of the stove. Align the roller with the hole. Secure the front end of the railing, roller ,and hole with the shoulder bolt using a 10mm wrench. Tighten just enough but don't over tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from Norman, OK
- Parts Used:
- WPY0314907
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven not heating, F3 trouble code.
Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Greenville, SC
- Parts Used:
- WPY0061732
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replace broiler element
Unscrew and remove old element, install new element.
Was this instruction helpful to you?
Thank you for voting!