AGR5725RDB Amana Range - Instructions

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.

The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!

I first tested the broiler and that worked so we determined that the igniter on the bottom was not working. I removed the grill and then removed the igniter ( it is attached with two screws and unplugs from the back of the oven. I then looked up the part we needed on the part select website by model number and found the exact one ( the picture was very helpful) We received the part in one day installed it and the oven is working better than ever.

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

Replaced oven controller. Have used Partselect.com more than once. Best prices, and fast, accurate service. Reliable.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

Remove two screws back panel and remove sensor two screws inside top oven.

removed door (no tools required - just lift and pull door out of range). removed front door panel with a screwdriver. removed/replaced door hinge with nutdriver. replaced front door panel with screwdriver. replaced door on range (again, no tools required). then installed tip-over bracket to floor/wall behind range. measured location, drilled pilot holes and installed wood screws into the floor and rear wall stud.

The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

followed instructions from repair manual.

My oven would not work. It took longer & longer to fire, finally died. I did an online search & found partselect.com, with it's very helpful troubleshooting info, and somebody posted info that 80-90% of the time it's the ignitor that has failed. I ordered it Sunday night, it arrived Tuesday. I took the door off for easy access, took the bottom of the oven out, removed the flame shield and replaced the ignitor. I tested it and it worked! The hardest part was moving the stove away from the wall & threading the ignitor plug thru the back of the oven. The cheapest appliance repair visit would have been $89 + cost of parts. Sears charges $129. I think I saved at least $100, thanks to partselect.com.