GBE22AA Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robin from Seneca, SC
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip bowls were all rusted.
Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Germantown, MD
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old drip bowl was worn out
new drip bowl fit perfectly and was a snap to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alison from Carnation, WA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drip pans needed replacing.
Put in the new drip pan -- which are really nice shiny ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowls
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowl
Remove old drip bowl from the range and put a new one back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Villa Ridge, MO
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vincent from Martinsville, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
electric surface unit not working
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Was this instruction helpful to you?
Thank you for voting!