ACS4250AB (PACS4250AB) Amana Range - Instructions

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.

I'm a woman that's very comfortable with tools, and this project took me about 3 hours because I worked slowly and meticulously. I first searched online for instructions and diagrams to disassemble the range top (which you provide on your site!); took the range top apart; disassembled gas cylinders; removed the clock assembly and found that the plastic "hinges" on the case "face" broke and that's why the clock assembly fell behind the stovetop. This piece is not available separately, so you have to purchase the entire electronic clock control assembly which is over $200. My clock control works perfectly, so I removed the clock overlay; cleaned the icky's off of everything; adhered the new clock overlay and then "McGyver-ed" the overlay case "face" back to the assembly with electrical tape, in a beautiful, not obvious way, and put it all back together. Re-hooked the gas and power and voila! It works! Cleaned up my mess and made some hot tea before bed. Now I can bake some cookies this weekend ?! Thanks for this site and the parts you offer! I'm a happy customer!!!

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Had to screw off old terminal block & screw on new one

turn the power off first, remove knobs, removed burners,disconnected wire from igniter,raise the top of the stove,re rmoved wire from the door lock removed two screws remove the door lock itself, then put all back on in same order as I remove. Main thing to remember is to writeyour colors of the wire down so you know where to replace them.

Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

Pulled range away from wall and unplugged it. Pulled smoothtop out a bit to clear retaining clips. Swung top up and unplugged the cable going to top. Removed top hinge so top could be removed. Put top upside down on a table to work on. Removed wires from bad burner and then removed screws holding the burner in place. Replaced bad burner with new one and reversed the previous steps. Range worked like new. PartSelect service was great, received the part in one day.

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

My husband did the repair. It was so easy that I could have done it. He had to remove 3 screws and then hook up the element. Nothing to it!!

Removed top of stove replaced heating element ,piece of cake.

Removed the old sensor which is held into the upper right of the back of the oven by removing the two screws and pulling the sensor out. Then disconnected the sensor from its connector. Replace the old with the new by simply clicking it into the connector. Then pushed the wire back into the oven wall and screwed the two screws back in. The whole job took about one minute to do after evaluating the process. While it was not necessary to remove the door, I did (which was very easy) and ended up cleaning the glass inside and out. All in all, a complete success. Oven working as new.