ALY1680ADS Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Flora from Lansdale, PA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Flames were coming out from under the burners. The bottom of burner was rusted
I ordered the two replacement burners. When they arrived I equipped myself with WD-40 spray, rubber mallet and a rubber gripper I used to use to open canning jars. Sprayed the WD-40 around the burner base and let it sit for 20 minutes. Made a mental note of the location of the sparker of the burner, to remember to put the new one in the same way. Gathered my courage and gently wacked the burner with the mallet all around it. Then grabbed the burner with the gripper and gave it a firm ¼ circle twist counter clockwise. It came apart with no problem. Disconnected the two electric wires by slipping them off their sockets. Removed all the loose rust and cleaned around the burner. Reconnected the wires with the new replacement burner and dropped it in its place. Wiggled it a little until it fit back into its original location and twisted it ¼ circle clockwise. Done, just saved myself the price of a new stove! Note: There is no need to shut off the main gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Casa Grande, AZ
- Parts Used:
- 74003929
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven door handle broke in two pieces
Remove two black Phillips head screws from the top of the oven door and two black Phillips head screws from the bottom of the oven door which releases the door from the oven. Remove the two Phillips head screws that hold the handle and discard broken handle. Install new handle onto door and then replace the door. Easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Richwood, OH
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
original grommets broken
The new grommets were NOT the correct parts, too big, so there was no repair.
Was this instruction helpful to you?
Thank you for voting!