AER5511BAW Amana Range - Instructions

(1) Disassembled range element cartridge unit by removing six machine screws on sides
(2) Removed old element receptacle assembly (note screww attaching the clip to ring was corroded and had to be drilled out and replaced - screw not included), retaining existing element (determined it was good)
(3) Fited up new element receptacle assembly and determined how far the new wires would go, cut the old wires at appropriate point (allowing for wire splice).
(4) Attached new element receptacle assembly using a machine screw I found in my collection
(5) Routed new wires though retaining clips, and spliced into old wires near the cartridge plug (note: be sure to use high temp splice nuts - not supplied in kit)
(6) Installed old element into new receptacle and tested by measuring resistance - element resistance should be about 12 ohms, with all connections to ground reading infinity)
(7) Reassembled cartrige assembly using six machine screws previously removed (note, make sure the part align properly - top inside the bottom)
(8) Put the assembly back on range - worked great!

Removed the old sensor by removing two screws and pulling the wire out through the hole. Disconnected the connector and discarded the old sensor.
Selected the correct connector of the 3 provided, plugged the new sensor in and threaded the wire back into the hole paying special attention to make sure wire and connector was on the backside of the insulation. Assembled the two screws and tightened.

This purchase was for replacement parts, not for repair. Installation was a simple matter of taking out the old and installing the new, which is extremely easy to do. One item was damaged; Parts Select was absolutely fantastic to deal with regarding replacement! One word of caution regarding the product - I mistakenly ordered Whirlpool drip pans which have an opening in the bottom, the Maytag pans don't. Initially I thought that it was a mistake by Parts Select; which wasn't the case. The pans fit perfectly so I kept them. If I reorder, I will be certain that I order the correct pans.

First, thanks to PartsSelect for getting the part to me so quickly. I went to the "Instant Repairman" , checked all that applied to my problem. The answer was the sensor, 99% of the time.I used a coat hanger to pull the latch back and open the door. I watched the video and followed the instructions to remove the old sensor. The wires were melted but the plug was still good. I used one of the adapters to install the new sensor, then replaced the two screws inside the oven. I pulled the stove out because I had read in the reviews that you needed to get the plug behind the insulation away from the oven wall. I was lucky ,there was a small hole in the back ,right behind the sensor.I gently pulled the wire and plug to the back ,well away from the oven wall. Put the stove back in place ,threw the breaker and was back cooking again!! My stove has a downdraft vent, took me longer to hook the vent back up than to install the sensor..Oh yes, did I say,I am a75 year old female and I did it all myself..

FIgured it was either a bad heating element or a realy expensive repair so I purchased a replacement element to rule out the simple and inexpensive possibility. Pulled oven out from wall and disconnected power supply. Removed retaining bracket from top of oven, two screws that held in heating element, disconnected from fittings, replaced with new element, and reattached screws and retaining bracket. Plugged in power supply, tested lower oven (it worked just fine) pushed oven back against the wall. Threw away the old element and packaging. Job done.

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

Removed bottom and side trim, slid the bottom trim onto the glass, and reinstalled the glass on the door. I think there were less than 8 screws total.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Purchased 2 piece broiler pan from this site

I raised the stove top to verify with a volt meter that electricity was truely going to the elements and which ones were receiving current. I removed the back panels to gain access to the controls and wiring. After checking the circuitry with the volt meter I determined that one of the thermostatic controls was defective. I ordered a new control and 8" burner (which showed signs of deterioration) from PartSelect and received them the next afternoon. It took less than an hour to reassemble.

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.