CBP26CBY Amana Range - Instructions

The top seal was too long (my fault, ordered wrong length seal) so I had to cut it and high-temp epoxy the metal hook into the end. Overall pretty easy fix.

Purchased 2 piece broiler pan from this site

The knobs were a perfect replacement and I just slid them onto the posts on which the old ones were on. Although my range is a Glenwood I think that the parts are now made my Whirlpool (not exactly sure) but they are a perfect match. My order came so quickly and I am thrilled with the transaction. I didn't think I would ever find the replacement knobs and thought I might have to get a new range as you could not read the oven temperatures at all on the old knobs.

shortened gasket for this oven. moved hook approx. 1 inch. used high temp adhesive. simple fix.

Took the old knobs off and put the new ones on...voila!!
They fit perfect and even had the same part number stamped inside. Perfect fit and just like new!
Wasn't much of a repair per se but wanted to give a good review. The old knobs were over 30 years old so I was worried I wouldn't be able to find an exact replacement but PartSelect had the exact match.

I pulled off the old knobs and then placed the new knob. No tools needed!

I have a gas oven range and 2 of the knobs were stripped, making it difficult to control the heat. My appliance is at least 20 years old. I thought I'd have to replace the whole thing. I found your website, did a search, and found exactly what I needed. The knobs fit perfectly. Although not an exact match to the originals, they work, and that's all I care about. Easy and inexpensive fix.

ordered new broiler pan

first i shut off the gas, then diconnected the gas lines that go to the thermostat itself, then i took out the 2 screws that hold it in place, and removed it completely from the stove. then i put the new part in place of the old part, and hooked it back up. turned on the gas, checked for leaks with soapy water, then ajusted the piolet light screws, lit the piolets and tested it out, workd better than new.

Ordered "right" thermostat. Installed "right" thermostat.

The repair was really easy! I read a review where the gentleman had order the wrong size and that had me a little worried because I did not specify a size. There were three seals on my range so I figured if one broke I might as well replace all three. When I received the seals they were the right size and it took me less than five minutes to put them on. No tools needed because they had hooks on each end. Thanks a lot!

I removed the old stretched and cracking seals by unhooking the metal brackets from the holes at the corners of the oven, and replaced them with the new seals, which fit perfectly. It took about a minute. My 25 year old oven is working wonderfully now.

The side seals were available and hooked into place with no effort at all. The OEM top and bottom seals were not available any longer so I purchased the recommended substitute which was about 2" too long. I took the advice from another of your customers and cut the top and bottom seals to the correct length and using hi-temp epoxy reattached the hooks to the shortened end. On an additional note the seal itself is partially tubular in cross-section an by that virture protects the hi-temp epoxy from the heat.

Used 2 side seals to make a new top seal (no longer available). Cut the 2 new side seals to provide about 1/2" less length than the old top seal. Removed one of the end hooks and straightened the hook, removed the old silicone from the hook. Used high temperature silicone and the old hook to splice the cut ends together. Let cure over-night and reinstalled. Works like a champ.

The side seals fit perfectly so I just put the hooks in the holes! The top seal was too long so I cut it to size and used super glue which did not hold. Next I looked for a high temp glue with no luck. Finally I put the hook into the seal and used a very fine wire through the holes in the metal of the hook piece and twisted the wire until it held the metal piece in place. Then I installed the top seal and it works fine. There is no longer heat pouring out the top of the oven and my brownies cooked at the right temp for the right time. Hooray!