AGS761LL (P1142635NLL) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Weston, CO
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broiler & burners worked, oven would not ignite or heat up.
Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from Norman, OK
- Parts Used:
- WPY0314907
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven not heating, F3 trouble code.
Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blaise from Deer Park, TX
- Parts Used:
- 32020101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burners would not light everytime they were used.
I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from portland, OR
- Parts Used:
- WP74011278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
oven light replacement
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mountain Ranch, CA
- Parts Used:
- R0706010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge broken
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willliam from Goldfield, IA
- Parts Used:
- WPY0314907
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gears and gear box top case cracked
Take top cover off take gear box cover off. check all gears for wear and clean all of above. Be sure you identify all parts needed before you order plus assembly grease!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Eagan, MN
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burners not igniting
Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and installed module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from UKIAH, CA
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.
Was this instruction helpful to you?
Thank you for voting!