ARR6300LL (P1143456NLL) Amana Range - Instructions

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

shut off circut breaker. un pluged stove removed back panel disconected 2 wires on element. removed 1 screw that holds element in place pull out old element put in new reassemble

Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.

Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!