AER5815RCB Amana Range - Instructions

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Turn off breaker to oven and verify no power.
Remove the two screws holding metal panel covering baking element on the floor of the oven (near back of inside of oven)
Remove two screws holding element mount to floor of oven (near front of inside of oven).
Remove single screw holding element to back wall of oven.
Pull element toward front of oven, carefully holding wires so they do not disconnect from element and slip inside the ovenback wall.
When you can reach the wire connections, hold each one with a pair of pliers and disconnect from element ends.
Connect new element ends into wire connections. Be sure to insert all the way into both connectors.
Carefully, push the wires back into the rear of the oven, trying not to scrape the wires on the sheet metal.
When fully inserted, reinstall single screw to secure element to back wall.
Re-install two screws to element mounting at the front of the oven floor.
Re-install two screws to secure element cover plate to the floor of the oven.
Turn on breaker for oven and verify oven has power.
Turn on oven to bake at 400 degrees.
Wait for oven to come up to temp and maintain for 10-15 min (you may smell some burning smells as the element heats up the first time).
Enjoy...

First I removed the two wires from the back of the stove. I then removed the two screws that were holding the element in place. Installed the new one without problems

Unplug appliance, unscrew small cover plate in rear. Disconnect wires from old element, may need to use needle nose pliers to wiggle clips off. Open oven door, remove false bottom to expose baking element. Remove baking element. Install new element, connect wires from rear, and replace covers and false bottom. Plug in appliance and test.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

removed bottom pan cover. removed broken element. replaced with new one.. simple. would buy from this place again. shipped super fast

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both side .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

Watch the video. Spot on instructions. Easy peasy.