AGS3760BDB Amana Range - Instructions

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

Remove two screws back panel and remove sensor two screws inside top oven.

This website easily diagnosed the probable problem. We ordered the suggested part and my husband replaced it, despite a slightly eroded, rusted screw that was stubborn to remove, in about 20 minutes. The oven is working perfectly. With tax we spent about 50 bucks. I was sure we needed a new oven. We, ironically, celebrated by going out to dinner!

removed the old defective ingniter and installed new igniter turned on the ove n and wala, it was like brand new.

I was sure my problem was due to a gas ingiter that was no longer working. I read about others that had the same problem as I did. I ordered the part from Partselect because they had a 30 day no hassle parts return policy.
I removed the oven racks and 4 screws to get to the igniter.
I unpluged the igniter, put the new one in, and replaced the racks. Very simple and easy to do.

I removed the cover protecting the igniter. I pulled the stove away from the wall to get at the connect for the igniter. I loosened the 2 screws which held the igniter.
Took the new igniter ran the wire to the back to the connection and mounted the igniter with the 2 screws. Turned on the oven to make sure it works and it did. Turned off the oven, replace the cover and pushed the stove back in place. No big Deal!
Your web site was very helpful. Thank you so much!

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

Tested power coming into unit,then tested power going to igniter,both of which were good.Did a continuity check of igniter element and found it to be bad.Ordered one from PartSelect,recieved it in minimum time,removed the old one,installed the new one,works like a champ.

After reading how others replaced their defective Gas Oven Igniter, I decided to attempt the project. My only mistake was Removing the Oven Door. Though it came off with ease, it was a complete bear to put back on.
Once I removed the oven door, I located the two phillips head screws that held the bottom oven floor in place. One screw came off without much effort, however the other stripped and had to be drilled out.
After removing the oven floor plate, I quickly located the Igniter and using a nut driver, unscrewed it. One of the two screws stripped on me and had to be replaced. The new part was put in position and the process was reversed. This is where I encounted a problem.
After repeated attempts, I soon found that the oven door hindges had to be held in the open position with a flat head screwdriver in order to be put in place. I found no instructions or info on how to complete this process (even from Maytag) and only completed the tast by trial and error. I highly suggest NOT REMOVING THE OVEN DOOR to complete the repair. The repair itself is rather simple even with stripped screws.