ALY2280ADW Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Godfrey from Las Cruces, NM
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of top burner igniter
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Tomahawk, KY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner rusted flames coming out the side of the burner
turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Oconto Falls, WI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner flame was poor and yellow flames left sute marks on pots and pans
twist old burner and lift out disconnect two wires throw away gasket (if there is one left) connect two wires to new burner set in and twist till tight total time 45 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Floral park, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the top broke away it was corroded
use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Vashon, WA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wore out burner and igniter
New burner and igniter.....actually it was very easy to to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bhavni from Richmond, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Plymouth, MA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber grommet for stove top cover
I ordered the grommet... Didn't match the others ... But it fit on , and will do the job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Bushnell, FL
- Parts Used:
- 74003106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
second oven rack
I was very impressed with the ease in ordering the part, and the speed of delivery. All I needed was a second oven rack so that when I bake cookies, I can bake two trays instead of one, I get done in half the time now. Thank you Part Select!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Mobile, AL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gas blowing out from under burners
As the video said, twist burner to the counterclockwise 1/8 turn. Lift the burner straight up. Disconnect the two wires. Remove the burner and reconnect the wires ( they only go one way so they cannot be connected backwards.) Place the burner over the gas fitting and turn the burner clockwise until snug. I turned the power off at the circuit breaker box. The video was extremely helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ZHENG from PINOLE, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
repair range burner
in and out in 15 min ,is easy when part fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Richwood, OH
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
original grommets broken
The new grommets were NOT the correct parts, too big, so there was no repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!