AER4111AAW Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from ROSENBERG, TX
- Parts Used:
- WPW10196406, WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip pans needed to be replaced
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald E from Rochester, NY
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip-bowls wore out
i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were working and they did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerard from Northport, NY
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned oit
Shut off the power to the stove. Remove the two screws retaining coil
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEFFREY from SUGAR GROVE, VA
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element Was Burned Out.
Very easy, with only the removal of 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Oldsmar, FL
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My drip pans were in bad shape
I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANNIE from LINDEN, NJ
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Baking Element In The Oven Had Broken
My husband did it was really easy ,he turned the power off to the stove,took the back cover off the stove with a screwdriver and pulled the old one out,then he slipped the new one in connected the wires ,it took less than 15 minutes that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stanley from south lake tahoe, CA
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken bake element
Took out two screws in the back of the oven that held in the bake element. Pulled the element out of the back of the oven to expose the wires. Pulled the wires off the broken element and then reattached the wires to the new element, put it back into place. Reattached the screws. Done in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlin F. from Holbrook, AZ
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace coroded drip pans
replaced the drip pans. Fit perfect. No problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Sturgeon Bay, WI
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat in oven
Your site really helped out alot. Job was farily easy and now we have heat. Difficult part was reaching the wires in the back. Thanks again! TZak
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Jamestown, SC
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element burned out
Actually a very simple repair. Determined that the problem was a burned out bake element since broiler worked fine. Looked up part on-line...diagram on PartsSelect made this very easy.
Ordered part selecting normal shipping (part arrived in 3 days). Repair: 1) turned power off at the breaker box 2) removed baking shelves. 3) removed the two mounting screws holding old bake element in place 4) gently pulled the bake element out of the oven until about two inches of electrical wire were exposed. 5) removed the electrical clips from the old bake element. This required steady wiggle to get them off. 6) attached the electrical clips to appropriate ends of new element ensuring they are well seated 7) pushed electrical wires back into the oven and mounted the element using same two screws. Turning the power back on at the breaker, I then tested the repair. No problems noted...turned oven off and replaced the baking shelves. Baked homed made bread that evening.
Ordered part selecting normal shipping (part arrived in 3 days). Repair: 1) turned power off at the breaker box 2) removed baking shelves. 3) removed the two mounting screws holding old bake element in place 4) gently pulled the bake element out of the oven until about two inches of electrical wire were exposed. 5) removed the electrical clips from the old bake element. This required steady wiggle to get them off. 6) attached the electrical clips to appropriate ends of new element ensuring they are well seated 7) pushed electrical wires back into the oven and mounted the element using same two screws. Turning the power back on at the breaker, I then tested the repair. No problems noted...turned oven off and replaced the baking shelves. Baked homed made bread that evening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Jesup, GA
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace oven heating element
The process would have been easy except the wiring to the element had a problem. One wire was too short which meant pulling the entire stove assembly out to reroute the wire.The part worked fine; the problem was with initial wiring of stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KIMBERLY from INDIANAPOLIS, IN
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element went out
Just followed the installation instructions offered on this website. WAS REALLY EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Atlanta, GA
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walid from Worcester, MA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bowl -Drip and gasket
it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid
Thanks for .
PART Select.
Best regard .
Walid
Was this instruction helpful to you?
Thank you for voting!