AGS1740BDW Amana Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.

Once I got the new Igniter, I unplugged the old igniter and took two bolts out. Then remounted the new igniter and plugged it in. Works like a charm!!

First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings

Changed the igniter

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

This website easily diagnosed the probable problem. We ordered the suggested part and my husband replaced it, despite a slightly eroded, rusted screw that was stubborn to remove, in about 20 minutes. The oven is working perfectly. With tax we spent about 50 bucks. I was sure we needed a new oven. We, ironically, celebrated by going out to dinner!

removed the old defective ingniter and installed new igniter turned on the ove n and wala, it was like brand new.

Tested power coming into unit,then tested power going to igniter,both of which were good.Did a continuity check of igniter element and found it to be bad.Ordered one from PartSelect,recieved it in minimum time,removed the old one,installed the new one,works like a champ.

Replaced gas oven ignitor

We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.

We took the interior floor out, pulled the stove away from counter, before that turned all electricity to the house off. Then we unscrewed the ignitor inside then underneath unplugged it and plugged in the new one, cleaned to oven and screwed the ignitor in and replaced the interior floor and we were done.

My oven would not work. It took longer & longer to fire, finally died. I did an online search & found partselect.com, with it's very helpful troubleshooting info, and somebody posted info that 80-90% of the time it's the ignitor that has failed. I ordered it Sunday night, it arrived Tuesday. I took the door off for easy access, took the bottom of the oven out, removed the flame shield and replaced the ignitor. I tested it and it worked! The hardest part was moving the stove away from the wall & threading the ignitor plug thru the back of the oven. The cheapest appliance repair visit would have been $89 + cost of parts. Sears charges $129. I think I saved at least $100, thanks to partselect.com.

I started with pulling the base of the oven to examine the mechanism underneath. The hardest part of the whole thing was working the wire connection past the metal back of the oven. It required prying the metal away from the frame rail and wedging the wire connection through. Other than that it was unplugging the old, plugging in the new, and a few screws to reattach the igniter, heat sheilds, and oven base.

After reading how others replaced their defective Gas Oven Igniter, I decided to attempt the project. My only mistake was Removing the Oven Door. Though it came off with ease, it was a complete bear to put back on.
Once I removed the oven door, I located the two phillips head screws that held the bottom oven floor in place. One screw came off without much effort, however the other stripped and had to be drilled out.
After removing the oven floor plate, I quickly located the Igniter and using a nut driver, unscrewed it. One of the two screws stripped on me and had to be replaced. The new part was put in position and the process was reversed. This is where I encounted a problem.
After repeated attempts, I soon found that the oven door hindges had to be held in the open position with a flat head screwdriver in order to be put in place. I found no instructions or info on how to complete this process (even from Maytag) and only completed the tast by trial and error. I highly suggest NOT REMOVING THE OVEN DOOR to complete the repair. The repair itself is rather simple even with stripped screws.

First I tried oven ignitor. Did not cure the problem. Then ordered short sensor and it cured the problem. Pull range out & unplug unit.From inside unit remove two screws holding short sensor in &pull out from inside. Unhook sensor. Slide in new sensor& secure with two screws. Had to remove two screws on back of oven to plug in sensor to existing plug. Very simple job.