ACF4255AB (PACF4255AB0) Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from cleveland, TX
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner Would,Nt Heat Up.
Removed top of stove replaced heating element ,piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hau from Burke, VA
- Parts Used:
- 31750717
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove Range Drawer Difficult to Open and Close
Insert one end of the railing into the slot in the back of the stove. Align the front end of the railing with the hole at the front of the stove. Align the roller with the hole. Secure the front end of the railing, roller ,and hole with the shoulder bolt using a 10mm wrench. Tighten just enough but don't over tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Fairport, NY
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the burner wasn't light up.
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from gardner, KS
- Parts Used:
- 31986601B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
switch was broken
simple repair 4 nut screws easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from West Des Moines, IA
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, PA
- Parts Used:
- W10823726
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Inner element dead
Pulled range away from wall and unplugged it. Pulled smoothtop out a bit to clear retaining clips. Swung top up and unplugged the cable going to top. Removed top hinge so top could be removed. Put top upside down on a table to work on. Removed wires from bad burner and then removed screws holding the burner in place. Replaced bad burner with new one and reversed the previous steps. Range worked like new. PartSelect service was great, received the part in one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Copperas Cove, TX
- Parts Used:
- W10823710
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner stopped heating
My husband did the repair. It was so easy that I could have done it. He had to remove 3 screws and then hook up the element. Nothing to it!!
Was this instruction helpful to you?
Thank you for voting!