ARG7302WW (P1143391NWW) Amana Range - Instructions

looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

After a standard trouble shoot, and finding the control PCB has the correct line voltage and the unit failure has more than one function failure with-in the unit operation, I replaced the Control PCB.
Removal and install took about 10 min, and the unit works fine, all automation is working properly.
Lance

Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.

First I had to take the drawer completely out of the stove to reach the igniter. I then removed the screws that held the igniter in place and removed it. I had to slightly modify the replacement part by squeezing it together to make it fit into the same space. I put the replacement igniter in place and screwed it down; put the drawer back in the stove and turned on the over to see if it would light. Bingo, job done!

Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.

Thanks PartSelect.com

1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.

I used your instructions

I removed the ignitor.
Ordered the matching part.
4 days later the part arrived and I installed the part.

Replaced glow bar/ igniter.

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,

Removed oven racks and bottom cover plate. Removed stainless steel diffuser to access igniter. Removed bottom storage drawer and unplugged connector for igniter. Removed defective igniter by by taking out 3 screws holding stainless steel mounting bracket in place. New replacement part had totally different bracket which prevented it from mounting in the proper orientation so I carefully removed defective igniter from original bracket and installed new igniter. New part was tacked in place by some sort of high temp adhesive that had to be carefully removed to allow it to be installed in old mounting bracket. Installed new assembly in the oven and when I tried plugging in the power connector I discovered the pins on the new igniter were the wrong sex; both sides had male pins! Removed igniter again and cut off the two pin connector and installed a brand new 2 pin molex type connector. I installed a mating connector on the original length of wire and connector that I cut from the defective igniter along with the heavy insulating material so I now had a properly mating set of connectors. Went through the mounting process again; successful mating this time. Oven lights in 50 seconds. If it dies again I'll have a connector of each
sex ready before repair.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.