ARR6300LL (P1142669NLL) Amana Range - Instructions

ordered new broiler pan

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

E. G. First we turned off the circuit to the range. Then with a flash light to see we removed the two screws that hold the element in place. We then pulled the element out about 3 inches and disconnected the two wires. . . Then connected the two wires to new element and put the ends back into opening and replaced the two screws that hold the element in place. The hardest part was getting to the back of the oven for an 82 year old and a 94 year old but we got it working again!.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

I took the old wires and plug off and replaced it with the new block it works fine

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

took out old element, replaced with new.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.