AGR5725QDW Amana Range - Instructions

I removed the cover plates on the back of the range since I didn't know where the m1/m2 module was located. I traced the wiring back to the clock and timer module in the console. I ordered the replacement part and it came the next day by FedEx. I replaced the failed part and every thing works except the oven. I have to get a meter to find out if I have voltage at the oven gas valve or if the part 74009227 is faulty.

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

First i turned off the gas and unpluged the electric to the stove. I removed the gas line and the screws that held the housing of the hood and valve assembly .Then i unplug 4 wires that operated the safety valveon the gas.Unthreaded 2 lines ,one for the oven and the other one for the boiler.I then replace the new hood and valve kit and put everything back together and the oven works just fine.

It was really easy, just lift the door off from the range, I set it down on the box that the hinges came in, took the six screws out to release the front fascia of the door from the back, hinges are right there, un-screw and install the new hinges, put everything back together in reverse and lift the door back on to the range, less than 10 minutes!

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.

Removed oven door, removed bottom of oven, removed old igniter, installed the new one and plugged it in in the back of the stove. Installed oven door and it works fine. .

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.