ARC700LL (P1142698NLL) Amana Range - Instructions

Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

First, I turned off the power to the house at the breaker box. Then I removed the broken heating element through the front oven door. I hoped this would work as it seemed from other reviews that some people pulled the oven out removed the back panel in order to access the element. I unscrewed the plate and then gently pulled the element out. I had a little trouble "unplugging" the element. When I tried pulling, it seemed they were stuck tight. Turns out you have to sort of jiggle the connectors and then they easily pull apart. Had I figured this out initially, the repair would have been under 15 minutes. Attaching the new element to the connectors, rethreading the wiring back into the holes, and then rescrewing on the back plate too the oven wall took just minutes. Easy peasy. So glad I spent $40 to fix rather then $500+ for a new oven!

First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws for the cooktop.I put in the new burner & it worked just like new.

I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!