ARG7600CC (P1143387NCC) Amana Range - Instructions

Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall

My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed the V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!

It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and lift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.

WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove.
Needed flashlight to see under stove.

Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.

Thanks PartSelect.com

looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

I had done this before, but a while back, so it took a little longer to disassemble and find the igniter. Once there, easy to troubleshoot with a meter. Reassembly was only a few minutes and part of that was finding a new nut, since I lost one. I had to remove the storage drawer, then remove a metal cover to get at the connections. I tested the power to the igniter and found it to be OK. I tested continuity and had some but very low. Pulled the diffuser and cover off burner to locate igniter. Ordered part,put it on and reassembled everything. Working fine.

I used your instructions

Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

Bought a new one. . Three years later =)

I pulled the ckt breaker, removed the oven drawer and disconnected the igniter. I opened the oven door and unscrewed the igniter holding bracket and removed the bracket and igniter. I broke the old igniter element when removing it from the bracket. When installing the new igniter in the holding bracket I broke the ceramic element. REALLY BE CAREFUL. Ordered a new igniter, very carefully installed it in the bracket, then rversed the removal process. It's not hard, you just have to be careful

I removed the ignitor.
Ordered the matching part.
4 days later the part arrived and I installed the part.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,