ACF3375AC (PACF3375AC4) Amana Range - Instructions

same as taking out old part and i misdiagnosed the problem ordered wrong part first and parts select steered me ito the correct part thank you

There are two elements to look at, one on top (broil) and one on the bottom (bake). Same element but may have different connectors. Double check before ordering.

Check and see if power is going to the ignitor. Do an amp draw test on the ignitor. The gas valve will not open if it won't draw the right amount of current. Sometimes it will glow but wont be pulling the right amount of juice. In my case it wasn't even glowing but it still looked okay. The mounting screws can break or strip upon removal if they are old. In my case I had to drill a hole, for a new screw, on the back one, and the front one tried to strip out. I might try a little heat next time before removing them. If no power is going to the ignitor when you turn on the oven it might be that the board has gone bad. The ignitor should draw close to 3 amps.

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service

Thinking we had a difficult/expensive repair, when the oven stopped working this summer - we just took advantage of the weather and grilled out. Apple season and the desire for fresh baked apple pie motivated us to action. We ordered the part - found simply on the site - it arrived promptly. A screw driver took off the oven bottom, we replaced the igniter and within 15 minutes our oven was working again. Why did we wait so long?

I first tested the broiler and that worked so we determined that the igniter on the bottom was not working. I removed the grill and then removed the igniter ( it is attached with two screws and unplugs from the back of the oven. I then looked up the part we needed on the part select website by model number and found the exact one ( the picture was very helpful) We received the part in one day installed it and the oven is working better than ever.

I turned off the gas at the back of the oven & unpluged it. I then removed the 2 screws that secure the oven bottom plate to the oven. Once removed, that exposes the oven burner & igniter. There are 2 sscrews that secure the igniter to the burner; remove those screws, & pull the igniter wires out, to expose the connector. Unplug the connector, & the igniter is free. Just reverse the process with the new igniter.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Plug in the element put the wires back in the hole and screws the element on and that was it. Worked great.

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

The biggest problem was gettng the correct ignitor, seems there are two. The first ignitor was the wrong one (I do not remember seeing any reference to which on the order page), but once I had the correct one my biggest issue was to get the stove out far enough for me to get behind it to take the cover off. Six scews and a disconnect and a repeat to replace and done. I must mention that the service rep was extremely helpful and easy to deal with and there was no language issue. The replacement part came in two days. I would definitely order more parts from this company

Removed plate at bottom of oven and unscrewed ignitor. Tipped oven forward and removed tiny back panel to reach plastic socket that disconnected ignitor from oven. Pulled ignitor out and awaited replacement part and did reverse steps. Oven ignitor worked right away.

For stovetop I ordered part and removed sheet metal screws from oven rear top panel after appliance was pulled from wall, gas and electrical disconnected. I pulled old spark ignitor module out and transferred colored wires to new module and snapped that into place. Replaced oven and presto, stovetop ignitors worked immediately.

i got the right part from u fast del.and had it fixed in 15 min. was very happy withu service thank u will buy more parts from u when i need them it was the same part i took out

got new horizontal igniter from Parts Select pulled stove out from wall unplugged old igniter took out bottom oven pan loosened two screws. used same two screws to put new igniter in place, put back bottom oven pan pushed bake button on front of oven and the old was lioke new again

I am sure I saved a bunch of money for an outside repair. It was so simple I was embarassed that I did not attempt the repair sooner. Removed two screws from old burner head lifted it up unplugged the electrode wire replaced with new burner head put the two screws back in place and I was finished.

The broiler igniter and oven igniter are the same - WITH ONE MPORTANT DIFFERENCE- the plug! I tried to just switch them since we dont ever use the broiler but could not, due to the plug. I think that is part of planned obsolescence ! Anyway, I left the door and the power on - you guessed it, rebel! If you get a tingle from replacing this part you shouldnt be trying to fix it on your own! I removed the oven racks, took two small screws from rear of oven floor out, removed base plate. Two more small screws released the defective part. Pulled the plug wire through the back of oven and unclipped the connector. Plugged new part in, tucked the wires back into the insulation, replaced two screws on the igniter. Test fired oven- worked like a champ. Shut burner off, reinstalled base plate and screws and put the oven racks back in. Easy!