Models > ACR4303MMS2 > Instructions

ACR4303MMS2 Amana Range - Instructions

Jump to:

All Instructions for the ACR4303MMS2
76 - 90 of 154
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Barbara from KAMUELA, AL
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
burnt out drip pans
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ray from Council Bluffrs, IA
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Replace burner drip pan
Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
TROY from YPSILANTI, MI
Parts Used:
814399
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bad Receptacle
I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Hamilton, OH
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Eroding burner drip bowls
Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dann from Glendale, AZ
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
reflecter/drip pans wrong size
Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gudrun from Santa Fe, NM
Parts Used:
W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replacement of drip bowll
take the old one out, but the new one in.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Irina from Green Cove Springs, FL
Parts Used:
W10196406RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DANIEL from sanborn, NY
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
the drip bowls had rusted through
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joanne from Negaunee, MI
Parts Used:
WPW10181986
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
paul from windsor, VA
Parts Used:
WP3148952
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
water pump went out
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
2 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Noah from Richardson, TX
Parts Used:
W10196406RW, W10196405RW
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
corroded, rusted drip bowls
replace
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Louisville, KY
Parts Used:
814399
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Element terminal connection loose caused overheating and carbon buildup.
Sanded element contact, replaced connector block. The easiest part of the task was ordering the part online. You made it unbelievably easy. I was amazed!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lynn C from Leesburg, FL
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Front large burner stayed on high
i personally did not do the repair..one of my neighbors did it and he said it was super easy..he pulled stove out from wall, unplugged it from socket, removed defective part, shortened clip that knob attaches to, installed new part with no problems whatsoever...plugged stove back in, pushed it back in place...burner now works fine! i was super impressed with the delivery of this part...ordered it on a Monday nite, it was mailed out the next day (Tuesday), and i received it Wednesday around noontime.. :)
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROBERT from SALCHA, AK
Parts Used:
WP3149400
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Burner control failure/unable to regulate temp.
Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Cornelius, NC
Parts Used:
WPW10181986
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ACR4303MMS2
76 - 90 of 154