AGS5730BDW Amana Range - Instructions

I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.

Husband did repair. He removed the
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

For the Ikea Range isg650ws01, the repair was very easy.

Step 1) Slide the range away from the wall slowly, verifying occasionally to not strain the gas or electric lines

Step 2) Unplug the range

Step 3) There are 2 phillips heads screws holding the rear panel in place. Remove the two screws and remove the panel.

Step 4) The cooling fan is held in place with 2 phillips head screws. Remove the screws and disconnect the electrical cord

Step 5) install the new cooling fan. The electrical plug can only be inserted one direction, so there shouldn't be a concern that you have the plug installed correctly. Match the original orientation of the fan in the unit. Re-install the 2 screws for the fan, and then install the rear cover. There are 2 slots that the panel needs to slide into in the bottom. Finish the install by installing the 2 screws you removed in to hold the rear panel. Plug the range back in and heat to 450°F to validate the repair.

one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.

Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.

Nothing mechanical was required! But the service was phenomenal. These are just a drop in part. I was thrilled that you had them, received them in one day without overnight charges, And the cost was very reasonable.

easily pulled old seal out and push new seal in place simple and quick.

You had the part at a good price and super quick delivery.

I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!