P1142148NL Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Shelly J from KAPLAN, LA
- Parts Used:
- WP3185804
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
igniter on top right front burner was shorting out,it would click but not ignite burner
removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hendersonville, NC
- Parts Used:
- WP3185804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
stove gas burner would not light?
TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from ROSAMOND, CA
- Parts Used:
- WPY07506601, WP4179282
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original knobs with number readings worn off
Took the old knobs off and put the new ones on...voila!!
They fit perfect and even had the same part number stamped inside. Perfect fit and just like new!
Wasn't much of a repair per se but wanted to give a good review. The old knobs were over 30 years old so I was worried I wouldn't be able to find an exact replacement but PartSelect had the exact match.
They fit perfect and even had the same part number stamped inside. Perfect fit and just like new!
Wasn't much of a repair per se but wanted to give a good review. The old knobs were over 30 years old so I was worried I wouldn't be able to find an exact replacement but PartSelect had the exact match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from CHICAGO, IL
- Parts Used:
- WPY07506601, WP4179282
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob writing worn off
I pulled off the old knobs and then placed the new knob. No tools needed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Alameda, CA
- Parts Used:
- WP4179282
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed 2 burner knobs for my 20+ year old range
I have a gas oven range and 2 of the knobs were stripped, making it difficult to control the heat. My appliance is at least 20 years old. I thought I'd have to replace the whole thing. I found your website, did a search, and found exactly what I needed. The knobs fit perfectly. Although not an exact match to the originals, they work, and that's all I care about. Easy and inexpensive fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from St. Remy, NY
- Parts Used:
- 1430322
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burners would not light sometimes
Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lancaster, CA
- Parts Used:
- WPY07506601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wrong oven thermostat
Ordered "right" thermostat. Installed "right" thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from CHICAGO, IL
- Parts Used:
- WP3185804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no ignition on right frt burner
removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Gretna, LA
- Parts Used:
- W10709871
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler door would not go all the way in.
Removed broiler door springs, removed door slide arms that attach to broiler tray, two screws on each side. Removed tray and replaced slide guides. Instassed in reverse order. Works great: Thanks, Best thing about this repair was that the parts ordered were right and fit..........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Columbus, GA
- Parts Used:
- 1430322
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front burners would not light.
First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Oxnard, CA
- Parts Used:
- Y07623602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace top oven seal
This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure
Was this instruction helpful to you?
Thank you for voting!