P1131824NE Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marc from Kirkwood, MO
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor was old and wasn't working
Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Milwaukee, WI
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would not light up.
My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gregory from sayreville, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
oven would not light/get hot.
I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Pittsburgh, PA
- Parts Used:
- WP314763J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vidanand from Rochester, NY
- Parts Used:
- Y0309074
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven glass imploded during use.
Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from East Syracuse, NY
- Parts Used:
- 786324
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broiler inoperative
For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from EAST NEWARK, NJ
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
old igniter would not light stove
Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from NAPERVILLE, IL
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven would not light
Removed old ignightor and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert J. from WESTMINSTER, MD
- Parts Used:
- 786324
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
NO Work.
Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Gastonia, NC
- Parts Used:
- 866294
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range oven door switch need replaced
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DENVER, CO
- Parts Used:
- WPY0307363
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
clogged grease filter
couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Silverthorne, CO
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ignitor changed resistance so gas valve wouldn't operate
The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from WILLITS, CA
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
no heat
found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lindsay from Clinton Township, MI
- Parts Used:
- 314819B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass on stove door shattered
Simply slipped the new glass front in and put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Belmont, MA
- Parts Used:
- WP314763J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wire Racks very old and very dirty
I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased
Was this instruction helpful to you?
Thank you for voting!