AER6603SFB3 Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lydia from SAN ANTONIO, TX
- Parts Used:
- W10807828
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had lost one of the drawer glide
Just attached the glide to the drawer. It just popped in. No problem.
took about 5 minutes.
took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from SALEM, OR
- Parts Used:
- WPW10200660, WPW10031790
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced screw
By hand screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Clermont, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from HARMONY, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
temp level uneven
after watching the video, installed the temp sensor. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from mesa, AZ
- Parts Used:
- W11230488
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
chemical etching of black painted finish on drawer front panel
took out the drawer by removing two fillips head screws, four more screws removed the drawer front. Two plastic push pins and the front panel was off. Put the new panel on secured it with the pins, attached it back on the drawer front, put in the screws and slid the drawer back in the stove, put the two screws back in, done deal!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from DEFIANCE, OH
- Parts Used:
- W11171119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burner went out
Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from MARGATE, FL
- Parts Used:
- WPW10310922
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
It break with the time
I order the part here, the first part never arrived, it was an empty package, the second part was breaking, the glass support was missing. Broken from the vent trim, then I was tired of it so I just put back the original broken part with some super glue on it, lol
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from The Villages, FL
- Parts Used:
- W11171119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from NORTH PORT, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Greensboro, NC
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Demon Possession
Our repair was extrodinarily easy. As my husband was taking out the old element and the oven was off, the element heated up and actually burned him. He readjusted it and it refused to heat again. We figured at that point that there must be a short, so we never even opened the box with the new element. A short time later we decided to use the top of the stove for soup and a small fire started in the oven. We turned off the braker at that point and ordered a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darin D from MASON, TN
- Parts Used:
- W11182108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat in oven
Broiler worked, Oven did not.
Remove two Phillips screws, unplug element, reverse for installation.
Did not correct the issue.
After replacing the oven temperature control also, it turned out the control board was the issue all along.
Remove two Phillips screws, unplug element, reverse for installation.
Did not correct the issue.
After replacing the oven temperature control also, it turned out the control board was the issue all along.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SAN ANGELO, TX
- Parts Used:
- WPW10434452
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Front dual burner would stay on.
First I threw the breaker for the stove to off. I pulled the whole stove out, removed the back cover, removed the knob from the faulty control switch and then unscrewed the two screws holding in the switch. I then pulled the wires from the back of the faulty switch, inserted the wires into the new switch, reattached the two screws that hold the switch in. I threw the breaker back on and turned the burner on long enough to make sure that both dual elements came on and went off like they should. At that point I reattached the back cover and shoved the stove back onto its' slot. All is well and all went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bobby from HERSCHER, IL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
range would not heat right
very easy watched the howto you gave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from Phoenixville, PA
- Parts Used:
- WPW10434452
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Burner either full on or full off. No medium control
pulled range from between counter cabinets.
Opened breaker. Disconnected plug.
Removed back panel. 12 sheet metal screws.
Pulled off plastic knob.
Removed 2 machine screws coding control switch.
Used flat screwdriver to pry off 2 connectors.
Checked part number matched new part.
Pushed connectors onto control switch. Only fit one way.
Reinstalled switch with 2 machine screws.
Reinstalled back panel Most time consuming to get 12 sheet metal holes to line up panel-to-range.
Reconnected 220VAC plug. Reset breaker.
Tested control switch could turn on a fraction of the burner.
Pushed range back between cabinets.
Somehow height had changed so perpendicular drawer interfered with range handle. Maybe foot rotated when pulled out?
Removed lower large pan drawer. Lowered right front range foot to raise range handle. 2nd longest time consumed.
Re-installed lower large pan drawer
Opened breaker. Disconnected plug.
Removed back panel. 12 sheet metal screws.
Pulled off plastic knob.
Removed 2 machine screws coding control switch.
Used flat screwdriver to pry off 2 connectors.
Checked part number matched new part.
Pushed connectors onto control switch. Only fit one way.
Reinstalled switch with 2 machine screws.
Reinstalled back panel Most time consuming to get 12 sheet metal holes to line up panel-to-range.
Reconnected 220VAC plug. Reset breaker.
Tested control switch could turn on a fraction of the burner.
Pushed range back between cabinets.
Somehow height had changed so perpendicular drawer interfered with range handle. Maybe foot rotated when pulled out?
Removed lower large pan drawer. Lowered right front range foot to raise range handle. 2nd longest time consumed.
Re-installed lower large pan drawer
Was this instruction helpful to you?
Thank you for voting!