AGDS901E (P1131827N E) Amana Range - Instructions

unscrewed the bracket holding the igniter in place then we pulled the drawer on the bottom out and disconnected the Igniter - then we took the unit out of the bracket replaced it and then put the bracket back into place screwed it in and reconnected the igniter and now it burns hotter then it has since we moved into the house two years ago.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.

First I turned off the gas supply to the oven and disconnected it. I then pull the oven out away from the wall. I then unplugged the power cord. I removed the oven door by lifting it off of it spring hinges. I then removed a lower plate that covers the burner element by pressing in a manner that it popped off. I then located the ignitor and removed 3 screws. All were easily removed. Carefully, I pulled the igniter out and removed the wires from the wires that supplied the current to the ignitor. Installation followed by working the steps above in reverse order.

Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.

Removed back panel, unplugged sensor, removed sensor from inside oven (2 screws), replaced with new part.

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Replaced the igniter. Took out the 20 screws holding the bottom plate of the oven. Removed the igniter and gas tube mounting screws and bracket. Took off the wire nuts that attached igniter to stove wiring. Carefully installed new ignitor, using reverse of the steps above. Igniter tip is very fragile, so beware as you handle. All went very well, and oven now works like a charm

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

I removed the screws(4) that held the old glass in place, cleaned the broken glass chips from the frame and carefully reassembled the door.

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.

First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013

Roommate did the repair..so I don't know. I did the research online, the igniter solved the problem. Saved us buying a new oven!